|
Show your rotary car build up. Show off your Rotary Car build! |
|
Thread Tools | Display Modes |
06-01-2010, 08:16 PM | #166 |
Respecognize!
|
i had to clip the sheet metal and add fender flares. I might have gotten away with doing some heavy rolling of the fenders but i went with "gratiutious amounts of space" method. No spacers, 0 offset, 8" width
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-01-2010, 08:27 PM | #167 |
Respecognize!
|
some crappy iPhone pics.
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-01-2010, 10:50 PM | #168 |
Respecognize!
|
i am really considering making a new engine harness from scratch using all shield military spec wire. i am having some rather annoying issues with interference and / or grounding problems.
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-02-2010, 11:39 AM | #170 |
Respecognize!
|
its not that hard once you get it setup. i just seem to be having some issues with things making it difficult to get anything down
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-02-2010, 12:31 PM | #171 |
Can't.Make.Up.My.Mind.
|
this a cool build. i subscribed to your youtube channel. car is lookin great!
__________________
'90 GTUs Stay up to date with my photography '06 Toyota Highlander Hybrid '10 Toyota Prius "Initial Success or Total Failure" |
06-02-2010, 02:44 PM | #172 |
IT'S ALIVE!
|
Subscribing because I want to use the same (type of) intake system.
So you're currently using a N/A block with the 6PI manifold and just have the ports wired open? I have been holding out for a turbo block to avoid the aux ports, but I may have to resort to this type of setup if my luck continues. |
06-02-2010, 08:54 PM | #173 | |
Respecognize!
|
Quote:
the lower manifold is a simply maz made one for the 6pi so there is no provision for the aux ports. eventually i need to build another engine. this one is a stocker from a vert i had with at least 230,000 on it at this point. and in other needs, im loosing pressure to the clutch, sooo need to see if its the slave or the master.
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
|
06-03-2010, 12:45 AM | #174 |
Respecognize!
|
im thinking about getting some Crager V-5 wheels for racing tires. hope to make a hillclimb this season if i can get the car to be more cooperative
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-14-2010, 08:46 PM | #175 |
Respecognize!
|
tach was cutting out. Replaced the trailing ignitor. Now its fixed!
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-23-2010, 11:12 PM | #176 |
Respecognize!
|
so i am starting up another leg in this story. Expect some decent progress coming in the next two months including making my own coilovers, caging, fixing some damned wiring, and more!
__________________
For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage | Facebook |
06-24-2010, 06:15 AM | #177 |
Can't.Make.Up.My.Mind.
|
car is lookin nice. i like the flares alot. dont wanna thread jack but check out my thread in the near future (probably later today) and there will be a little project a friend and i are in the process of that i think you will like keep it up man
__________________
'90 GTUs Stay up to date with my photography '06 Toyota Highlander Hybrid '10 Toyota Prius "Initial Success or Total Failure" |