|
Quote:
Believe me I am trying! I may even trailer it up to a shop ifi do not get it figured out. I am way over due for some seat time..... BTW.. Nice passes and very consistant! |
I think if i wasnt afraid to launch harder it would have been in the 10.7's.
Keep us informed and good luck. |
One of the runs
Here is one of the runs!
http://www.youtube.com/watch?v=omr1HxIeSRQ What do you think? Needs more RPM'S right.:driving: |
That looked like a nice launch! Nice squat! You consider coming down for SFS event in 2 weeks? Ernie T will be there!
|
Hey busted, I added your best time from the Test&Tune. Could you please make a post of your major mods and what engine/trans/etc you are running? A slip would be nice as well. Thanks!
|
Quote:
|
|
2 Attachment(s)
My timeslip...
http://www.rotarycarclub.com/attachm...1&d=1224984127 performance mods: Brand new engine 99 spec RZ twins (sequential) upgraded sequential solenoids Apexi PFC w/ Datalogit RadiatorWorld.com aluminum radiator 850cc/1200cc injectors Walbro 255 Areomotive FPR Innovate Motorsports LC-1 wideband Defi fuel pressure gauge Defi Red Racer boost gauge Greddy Profec type-S boost controller Greddy CAI w/ K&N filters HKS turbotimer HKS twinpower HKS downpipe Pettit resonated midpipe Racing Beat single tip cat-back RPS clutch XSPOWER SMIC |
Year/Model/Trim?
I'll get you added on as soon as I get the above info ;) |
Sorry... 93 Vintage Red R1
|
Added! Thanks!
|
1 Attachment(s)
'85 base model, unopened ~180k mile '87 NA motor, 12lb. flywheel, Racing Beat header, full exhaust, 5th and 6th port sleeves and actuators removed, Racing Beat underdrive pulley, GSL rear w/ 4.30s and miata torsen, 185 all seasons.
R/T .318 60' 2.057 330' 5.928 1/8 9.161 MPH 76.84 1000' 11.984 1/4 14.374 MPH 94.44 Car 60 |
drewski,
Nice time! I added you on. Now how about some pics and details of your fast RX-7? ;) |
1 Attachment(s)
It's not much to look at. It's stock other than the motor and rear end.
Suspension, new exhaust setup, and S5 intake manifold are the plans for this winter. Hoping for 13s in the quarter on stock motor next spring. |
Still, nice times and welcome aboard. Have a look around and make some posts. Post that baby in the 1st Gen section, she looks nice and clean to me.
|
Here is my NEW pass to add to the list:
RT: .141 60': 1.508 1/8th: 6.9@100.70 1/4: 10.754@126.62 ViD: http://www.vimeo.com/2318181 Mods: Arizona Rotary Rockets small street port 67mm turbo Haltech E6K Alcohol spray Q-16 25 lbs of boost Run was done yesterday the 22nd of Nov, Tucson AZ. 74 Degrees temp, 6% rel hum, and 2980 elevation. |
Soooooo close to #1! Added on on (and you are the quickest 60'). Great pass!
|
1 Attachment(s)
Finally a site that does this!
1987 Rx7 TII 13bt small streetport Corksport 80mm turboback exhaust 3" TID Stock S4 turbo running 12psi Greddy V-spec FMIC 550cc and 1600cc injectors Walbro fuel pump ACT PP and modified disk Haltech E6k (tuned by me) MBC - homemade ball and spring type Tokico blue struts and eibach springs stock 5-speed bald 225-50-16 dunlop sp sport 8000 |
Welcome antman! Hope to see you posting around. Nice time, and I already added you. Tell your friends so we can populate the list more.
Oh, and work on your RT and 60'! :P |
85 Rx7
Motor- 13BT Street ported Trans- Stock T2 trans ECU- Microtech LT 10 Turbo- R85 8.8 Rear BEST Time 10.25 @ 23 lbs 60ft 1.37 MPH 136 Gas-C-16 Missed 3rd gear Low boost- Time- 10.86 @ 13 lbs 60ft- 1.42 MPH- 125 Pump Gas STREET CAR.. Tagged up drive it on the weekends.. The 10.25 Run... http://www.youtube.com/watch?v=kxrio...e=channel_page If you more info PM me.. Thanks dwrx7 |
^ Thats so SWEET!!
GREAT RUN!!!! |
Holy jiblets! You must post more on that car, it's INSANE!
|
Quote:
|
Very nice.
|
Quote:
Just saw the 8.8 solid rear... That makes a big differance... Kinda what I am thinking about on top of a c4! |
ran 6.8 @106 tonightin 1/8th. I will scan the slip but heres the video
|
You have to convert it to 1/4 mile time...
Your 1/4 Mile ET is 10.85 seconds computed from your vehicle 1/8th ET of 6.89 seconds. Your 1/4 Mile MPH is 131.51 MPH computed from your vehicle 1/8th MPH of 106.06 MPH. |
Quote:
|
That's why we need to get down to Steel one Friday night...
|
I am ready!
Here is another example. Turbor1 (enzo's bro) went : 1.49 60 4.3 330foot 6.82 1/8th 101 mph 10.6 in 1/4 @ 130mph to my : 1.56 60foot 4.5 330 6.89 1/8th @ 106mph I think that would have been atleast a 10.5 pass for me... |
Nice run Mike! she looks badass!
|
thanks man... Let me know if you want that dyno graph faxed to you or if you come to the gap I can bring it..
|
Awesome pass! Unfortunately we have to be fair and use the same calculator for everybody on 1/8-to-1/4 conversions. You just have an excuse to hit a 1/4 mile track now ;)
|
its no big deal how you want to post it. I was just posting the truth. In fact another example is Zinx 10.73 pass above. He had a 1.5 60, 4.52 330, 6.9 1/8th @ 104 then a 10.7 1/4.
I plan on having some more slips very soon ffrom the 1/4 track... |
I know the truth is usually far different then the conversions, but that's what we have to work with.
|
I ran a 12.45@112 the other day. I posted the video in the 1st gen section.
i have a slip but i need to get it scaned Steve |
Quote:
|
All updated. Good job fellas!
|
My friend rx2 with a stock chassis using a gforce tranny. He's going to give me the time slip later.
60' 1.49 1/8 5.9x 122mph 1/4 9.23 147mph |
He'll need to join RCC and post on his own if he wants to be on the list.
|
| All times are GMT -5. The time now is 03:51 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Hosted by www.GotPlacement.com