oil pan braces
 

I have a few oil pan braces ready to ship . These have the groove milled in them so the actually put pressure on the rail .

What's the cost on these? Nevermind. I just found the thread where you are bringing some to the Gap.

Bump, for a good product we have been using these for our customer engines.

Thanks again for bringing these to the Gap and letting me pick your brain while there.

any more in stock

There are seven more ready to ship .

what is the price for it?

The price for the oil pan brace and the engine torque brace is ( each ) $ 125 if you send me a check or for Pay pal ,through Dubulup on the other forum is $ 130 .

Do you still have some left?

Yes I have a few, Speed For Sale may have some as well .

This is a great product!!! I run it on my silver FD and will be picking one up for my red one when I finally pull the engine.

David, I never did have a chance to get the measurements on the engine torque brace before I left , but I'm hoping to when I am home for 2 weeks in October... will that be an issue? Thanks!

Brent

No problem ,stay safe.

What is your paypal info
thanks

Oil pan braces are ready to send out ,11-06-08

question: if my engine has a full oversized guru stud kit(machined block) would it be a waste of money to put one of these on?

If you are using the stock oil pan with drilled out holes then the brace is for you .The holes have made the pan rail weak and the brace willimprove things .The holes in the brace will to be drilled out as well .The brace is 3/16 thick and will still reinforce the pan to keep it from distorting .

Will this work well with stock oil pan and no modifications (I have a leakage >.<) Please let me know for I will paypal once confirmed. Thanks in advance.

p.s. Please pm for I dont check the forum alot nowadays. Thanks again.

-AzEKnightz

Pm to you and yes this will work on stock pans .Most people have stock pans ,some with studs and nuts . The groove cut in my brace is the feature that lets the brace do its job ,with out the groove the brace will not contact the pan rails width fully.

These are a great brace. Once I installed mine I understood why this is the better brace out there.
Man, am I lucky to have a friend like David living so close to me and makes great products for my RX7's

Is the oil pan brace still available? I have a leaking oil pan and would be interested in getting one.

THERE are a few ready to go

I'd like to order one ASAP, I shall PM you with details :)

I have received certain products from David my self and i can tell you first hand he takes pride on what he does and the parts are top notch.

I have a new batch ready to ship with the bolts and o-ring The price of the steel went up but the price will be the same .

They are $125 includes shipping $129 paypal .Includes high grade longer pan bolts (19) and longer motor mount bolts (6) . This is the only one with a milled groove to clear the pinch rail on the stock pan,so full presure is applied to the pan .

I want to pick up one of these. What is your paypal?

Anyone have pics ??

I think Howard Coleman does ,he uses them on the engines he builds .This is the only brace with a milled groove to fit over the pans pinch rail so full pressure is given across the rail .I drill the two missing holes in the late model pans and use all 19 ( included ) 6mm bolts .I notch the motor mount to clear the new bolt head . The motor mount bolts and the oil level sensor o-ring come with it as well .

This looks great, sending you a PM now!

I have a few more ready, do not wait to long.

Hey David! Thanks for the invite to the forum :)

I am sending the $125 via PayPal right now. Thanks!

I have your address Adam and will ship the part tomorrow .Thank you.

Thank you!

I sent you a PM with the tracking number .

$129 Paypal for the brace sent.

RB I will ship it tomorrow ,Only a few in stock .

i will be ordering mine with in the next couple weeks ( set aside a ETB and a pan brace for me... thanks

Pulled from storage and saved .Running out of oil pan braces should I make more .