Rotary Car Club

Rotary Car Club (https://rotarycarclub.com/index.php)
-   RX-7 2nd Gen Specific (1986-92) (https://rotarycarclub.com/forumdisplay.php?f=37)
-   -   trouble removing old bolts please help (https://rotarycarclub.com/showthread.php?t=12883)

dr50376272 12-04-2010 06:26 AM

trouble removing old bolts please help
 
i dont know if this is the right place to ask, but i have 37 year mazda rx4 bolts on my air conditioning and oil cooler, and i cant remove them. what do you guys do to unscrew old bolts that are stubborn and recalcitrant? (my website is www.kagoshimaenglish.com/rx4.htm for pictures of my car).

i also made a video here to explain my difficulties:

http://www.youtube.com/watch?v=yAY1RKTDJ-o

thanks for your help good people !

best regards,

david

N.RotaryTech 12-04-2010 07:25 AM

Try penetrating lubricants, "PB blaster", "WD-40", etc.
Also maybe heat the nut with a propane torch.

Looks like you'll need to redo the flare-nut piping too.

Good luck.

Pete_89T2 12-04-2010 07:32 AM

Didn't have a chance to look at your video, but try PB Blaster - it's a penetrating lube (like WD40) that works wonders on rusty old bolts. Give it a generous shot of the stuff, and let it soak in - if these bolts are really corroded, give it LOTS of time to soak in (many hours). When you do try to loosen it, make sure you use the right tool for the job - you don't want to slip or round off an already corroded bolt head.

willnordacgreen1211 12-04-2010 07:34 AM

1 Attachment(s)
here ya go!

http://rotarycarclub.com/rotary_foru...2&d=1291466036

dr50376272 12-04-2010 07:49 AM

cant buy this stuff in japan. bolt isnt rusty, just wont budge. i can bench press 300lbs so even with my strength it wont budge !

Pete_89T2 12-04-2010 09:12 AM

Quote:

Originally Posted by dr50376272 (Post 133846)
cant buy this stuff in japan. bolt isnt rusty, just wont budge. i can bench press 300lbs so even with my strength it wont budge !

Sounds like it's seized. Is it a dissimilar metal situation? As in a steel bolt in an aluminum threaded hole? Regardless, let it soak in the penetrating oil a good long time as suggested, try again. Use the longest handled breaker bar you can get in there. If it still won't budge, try an air impact wrench, preferably one that can deliver several hundred lb-ft of torque. If that fails, you might have to drill the stud out, retap the hole and get new bolts.

N.RotaryTech 12-04-2010 01:40 PM

Those kind of stuck bolts really suck, cause its only held in there by the tubing.

All I can think of for now is, use said lubricants, also use a flare-nut wrench so it don't slip off, and maybe clamp some vice-grip pliers on the fitting to hold it in place while you wrench on the nut.

JustJeff 12-05-2010 04:24 AM

What I did with PB Blaster when I was pulling my motor was hit the problem bolts and let them soak for a couple days. I had time till the motor was coming out so I'd hit them once or twice a day for a couple days. When I finally got to pulling the motor the bolts came loose with no problems.

Not sure if that advice helps with seized bolts, but if you have time to wait then it certainly won't hurt anything.


All times are GMT -5. The time now is 04:37 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Hosted by www.GotPlacement.com