NA SemiPP 20b
 

Updated 6/4/2019

https://www.instagram.com/reddozen12/

Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.

Goal 450WHP

Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping

Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals

Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
Going to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan

Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually

Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission

Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)

Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift knob
90's Mazda Speed seats
Volk SF Challenge wheels

Should be cool if this gets finished. You plan on passing emissions with this setup?

You have a target completion time frame.

That's why we're keeping the stock ECU. If you turn off all the codes (AP, Mazda Edit or Racing Beat flash), and allow all the readiness checks to set, it should pass.

I have no clue on the time table... it's really up to all the hands it has to exchange, and just how far over budget it goes...

Best case... I would say September?

Sweet man, look forward to seeing this completed!

I set my goal for 6 months too, its now turned into 3 years lol. Be ready for setbacks along the way.

Believe me I know. We'll see where things fall. September is an absolute best case scenario. Things never work out for me quite so nicely.. lol

Do I have to be the asshole?

of 2019?

And some not even by your own doing. Projects like that are never going to be top's on a shops list because they aren't money makers. They are in the sense that they're rolling advertisements, but the amount of time that fabrication takes and the amount that actually gets billed are two totally different numbers.

At Speed1 we would rather do engine jobs and dyno's all fucking day than the big project cars for the money, but the reality is if you can pull two blown REW's before lunch and bill 18.4 hours for it, you're gonna make a shit ton of money. But when you spend two days building an exhaust system, you're not actually going to bill 18 hours for it. Even if you do, you're still paying someone 18 hours and billing 18 hours, where if you can R&R an engine in a day, you'll pay someone 9 hours and bill 18.... so shops generally let the big projects sit until shit gets slow.....

Just my experience

And lets not forget because Rotary :smilielol5:

Sell it to me and let it sit for 5 more years.

Ain't that the damn truth, I still haven't seen your car!

Unicorn bruh..... Unicorn.

Like I said we'll just have to see.

Speaking from experience with the AP on my Speed3.... it doesn't let the readiness codes set. It masks the CEL but when they check at the emissions place it will say not ready and they will say "Did you disconnect your battery recently? You probably just need to complete your drive cycle."

Example:

I had the EGR removed and cat... EGR and cat both still said "not ready" after a full tune on the AP. You are allowed 1 not ready though.

AP for the RX8 still allows for readiness checks to be set normally. I reset my stuff all the time. I have all the cat codes turned off and pass emissions every time. So none of that concerns me having dealt with the bridge port for years.

I think the RX8 only set the not ready if it receives a mill code, but since it can't throw it, it always sets ready. My only not set check is the air pump. I may have a circuit made to fool that one.

You're not the first person I've heard about that from with the speed3.

Different protocols for the ECM.

I'm STILL waiting for that Christopher W guy to get his 20B FC going...

Granted, he has the engine in the car, but I bagged on him like TWENTY YEARS AGO on the Evil Forum...


-Ted