FS:Seals and Such
 

Here is what I have for sale:

Mostly complete Engine Seal Kit - Missing one outer water seal andoil drain crush seals. I decided to up rate everything else with Viton and originally used seals instead.

So I can either order all the missing parts for you and see the kit for $350 or piece part it. Shipping is extra.

http://rotarycarclub.com/attachment....1&d=1220829170

http://rotarycarclub.com/attachment....1&d=1220829195

http://rotarycarclub.com/attachment....1&d=1220829227

Re-Amemiya Reflashed ECU - Seletable two stage boost - 12psi and 14 psi
This ecu will support the following mods - Intake, full exhaust, intercooler, street port, 99 efini twins. The AFRs are on the rich side for safety. Looking to get $450 shipped. This ecu comes with the a switch that looks like the center console fog light switch (for that hidden look).

http://rotarycarclub.com/attachment....1&d=1220829265


20B Throttle body elbow - make reasonable offer.

http://rotarycarclub.com/attachment....1&d=1220829510

Viton water and oil control seals - 2700 miles put on seal, all are in good condition. $300 shipped (these seals aren't cheap, your looking at $550 worth of seals new)

http://rotarycarclub.com/attachment....1&d=1220833383

http://rotarycarclub.com/attachment....1&d=1220833383

4 brand new 850 side feed injectors - Nippon Denso units (don't let the SARD boxes throw you off) - $130 shipped or $475 shipped for all four.

http://rotarycarclub.com/attachment....1&d=1220833383

Stock Fuel Filter - 2700 miles on unit - $15 + shipping


http://rotarycarclub.com/attachment....1&d=1220833383


K&N Air Filters for Twin Turbos - $30 each shipped or $50 shipped for both

http://rotarycarclub.com/attachment....1&d=1220833383

Viton Seal Material - $10 per foot - 24 inches wide. E85 guys this is the stuff you need.

http://rotarycarclub.com/attachment....1&d=1220831268

Intake or Brake Ducting - 3 inch Diameter - 25.5 inches long - $25.00 shipped

http://rotarycarclub.com/attachment....1&d=1220831278

http://rotarycarclub.com/attachment....1&d=1220831285

4" T-Bolt clamps with springs - the good stuff - $15.00 each shipped

http://rotarycarclub.com/attachment....1&d=1220831331

3 omp injector resistors for 1600/1300 secondary injectors - New never used - $7 each shipped

http://rotarycarclub.com/attachment....1&d=1220831342

Aeroquip fuel lines:

3/4" - 54" - $25 shipped ($57 from vendor)

5/8" X 100" - $60 shipped ($110 from vendor)

3/8" X 25' - $300 shipped ($450 from vendor)

5/16" X 72" - $100 shipped ($210 from vendor)

http://rotarycarclub.com/attachment....1&d=1220832087

Aeroquip and Frugola -10AN 90 Degree Reuseable fittings - $15 Each + shipping

http://rotarycarclub.com/attachment....1&d=1220832098

Aeroquip Fittings:

180 Degree - $27

Tight 90 with 10An Male end - $25

Fuel Distribution Block - $100 ($150 new) shipped

Adaptor fittings - $8 each (1 -8AN and 1 -10AN) shipped

Frugola Straigth Reuseable - $12 shipped

http://rotarycarclub.com/attachment....1&d=1220832107

Stock Pressure and Vacuum Chambers - $5 shipped

http://rotarycarclub.com/attachment....1&d=1220832119

Check Valves - in good condition - $2 shipped

http://rotarycarclub.com/attachment....1&d=1220832126

Stock Electronic check valves

$10 each shipped

http://rotarycarclub.com/attachment....1&d=1220832702

EGT exhaust temp sensor clamps - $5 each
EGT exhaust temp sensor screw in units - $2 each
Stock WG control valves - $10
Oil pedestal (ported for improved flow) - $2

http://rotarycarclub.com/attachment....1&d=1220832739

20k mile stock Auto radiator - really clean item - $50 shipped

http://rotarycarclub.com/attachment....1&d=1220832779

Greddy to Synapse BOV Adaptor - $15 shipped

http://rotarycarclub.com/attachment....1&d=1220832809

Brand new Mocal inline oil temp/pressure sensor adaptor - -10AN male ends - $45 shipped ($58 from Pegasus Auto Racing Supplies)

http://rotarycarclub.com/attachment....1&d=1220832826

Sold - Brand new Mocal inline oil temp/pressure sensor adaptor - -10AN male ends - $45 shipped ($58 from Pegasus Auto Racing Supplies)

Adam, Do you still have all the AN fittings?? I might need some of those.. also I'll take the turbo control solenoid:)

Not to be a PITA but the engien seal kit - "missing one outer water seal and oil drain crush washers"...........and that's it?

So it has oil control ring springs, seals, scrapers?
Side seal springs?
apex seal springs?
corner seal springs?
dowel land o-rings?
front and rear mains?

Doing a rebuild on another keg soon - very interested in some info, thanks :)