Quote:
Originally Posted by vex
Well the digital dash is already a certain. I need to verify the inputs first and what I can afford. Consequently from the stock sensor suite does the FC have Oil Temp?
|
No it doesn't. There are a bunch of options for mounting it though. I have the first produced RE-Speed adapter tower with the -10AN fitting on it for both pressure and temp. You could also just use a generic -10AN coupler with an 1/8" npt port. I would kinda prefer to know what the temp is as it exits the engine, rather than as it goes back in. I think that information would be more usefull even if it is scary as hell.
Quote:
Originally Posted by vex
I don't have a Low coolant sender that works anymore (Ruined my low coolant sender when I attempted to mount it to my old radiator--may pick up a new one and try to find a nice round stock and actually get it drilled and tapped for the proper threads this time),
|
Stock one won't work. You'll need to get something that latches to grnd.
Quote:
Originally Posted by vex
I'll also need to figure out if my low sump sender works anymore (some reason I don't think it does).
|
Same thing, need something that latches to gnd.
Quote:
Originally Posted by vex
Fuel Pressure... I think I might hold off on that (as it would require purchase of a new sender).
|
Suck it up man, get the AutoMeter replacement senders. They're Delco or Dephi replacements for like $90. It's good info to have ESPECIALLY on a boosted engine. You know my history. With pressure vs MAP you can make a correction table that could keep you from chunking an engine.
Quote:
Originally Posted by vex
Quick question: Can Digital Pulse Inputs (DPI) be used as a Digital Switch Input (DSI)?
|
On the MoTeC's - yes
Quote:
Originally Posted by vex
Alright, another question for the general community: How does the Digital Dash hook up to the ECU? I'm assuming via the CAN bus system, but after going through both the dash manual and the ecu manual I don't see any instructions on installation to the ECU.
|
CAN bus is the way. Setup is specific to the combination. Which dash are you going with?
Quote:
Originally Posted by vex
|
I'll check it out in a bit..... going to weld a fuel cell
__________________
-The Angry Stig-
DGRR 2009, 2011, 2012 & 2013 - Best FC
DEALS GAP!! WOOHOOOO!!!!!
2015 Audi S4 - Samantha - Zero Brap S4
2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter
2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins
1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle
1988 'Vert - In progress
1988 FC Coupe - Gretchen -The attention whore BEAST!
I'm a sick individual, what's wrong with you?
I'm pure Evil
I'm still insane, in the best possible way.
I think Brian's idea of romance is using lube.
Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion.
You win with your thread. Most everything
It's a truck with a steel gate on the back. Just a statement of fact
Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff....
No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon.
-Angry Motherf*cker Mode ENGAGED-
|