|
Jack Coxe - 3rd gen - 2nd place
1994 Mazda Rx-7 with Popular Equipment Package with approx. 111,000-miles modified by myself with mucho assistance from Gorilla RE
Engine:
RP/rx7.com street port, 3mm apex seals, balanced rotating assembly
Unorthodox anodized full pulley set (main, w/p, alt)
Mazdaspeed engine mounts
Garfinkle oil pan brace
Intake:
Ground Zero / Excessive lower intake manifold (with Gorilla RE extra injector bung plugs)
Gorilla RE upper/lower intake manifold port matching
Gorilla RE ported throttle body
Double-throttle AWS wax rod removed
All unused Upper Intake nipples removed/plugged
Jet Hot cerama-chrome coating upper/lower intake manifolds
Turbo Blown LIM heat shield blanket
Sport Tuner throttle body polishing with nickel plated linkage
Turbo:
A-spec 500R with long runner manifold (Gorilla RE prepared: smoothed compressor inlet, rough casting welds flanges protruding bolts ground smooth)
Tial 44mm waste gate
Gorilla RE 1-3/4 inch waste gate dump tube
Tial 50mm blow off valve
Blitz sbc-id boost controller
Earls -4 & -6AN super stock hose & fittings for water, W/G & BOV lines
ATP -3AN stainless steel oil feed line
Earls -10AN Perform-O-Flex stainless steel oil return line with swivel seal fittings
K&N air filter with Gorilla RE 45 degree aluminum inlet pipe & 45 degree blue silicone coupler
Sport Tuner high-temp black ceramic coating exhaust manifold & turbine housing
Sport Tuner cerama-chrome compressor housing
DEI black fire sleeved oil, coolant, & wastegate lines
Thero-tec heat sleeve a/c lines & misc. wires
Thermo-tec adhesive backed heat shielding on fire wall, ABS shield and inner fender
Intercooler:
Crooked Willow stock mount IC (Spearco 13x17-in. core with carbon fiber duct)
Gorilla RE polished aluminum piping
Greddy throttle body elbow
Hose Techniques blue silicone couplers with Breeze clamps
Exhaust:
Gorilla RE 4-inch stainless steel downpipe
RP/rx7.com - Greddy 3-3/4 inch race exhaust
DEI titanium wrapped downpipe
DEI fiberglass wrapped mid & rear muffler sections
Thermo-tec muffler shield on mid-muffler
Fuel System:
Injector Dynamics 725cc primary / 2000cc secondary injectors
KG fuel rails with Sport Tuner cerama-chrome coating
SX Performance fuel pressure regulator with -3AN stainless steel boost line
Apexi BNR33 pump
Chuck Westbrook fuel pump wiring mod (direct power to relay, 10-ga. power wire from fuel pump relay to pump, extra ground at pump)
Earls -6AN feed/return Perform-O-Flex hose with swivel seal fittings (routed using Earls hose separators mounted on OEM feed/return brackets undercar)
Hyperion surge tank cover
Kinsler ANO-BRL 10-micron in-line fuel filter
Ignition:
HKS Twin Power amplifier
Turbo II leading coil
Magnacore 10mm wires
Gorilla RE remote coil mount bracket (in place of removed power steering pump)
NGK R7420-9 & 10 spark plugs
Engine Management:
Apexi Power FC with commander
FC datalogit
Dudeman fast acting air intake temperature sensor relocated to intercooler outlet pipe
Gorilla RE tuning
Race Logic traction control
OEM map sensor with -4AN super stock hose and fittings
Cooling:
Koyo radiator
Mazmart remedy water pump
Evans coolant
FC thermo switch
Thermo-flex radiator hoses
Earls -4 & -6AN super stock hose & fittings
Sport Tuner cerama-chrome water pump & thermostat housings
OEM polished coolant filler cap
Oil System:
Crooked Willow dual oil cooler kit using Mocal 19-row coolers, Mocal thermostat, Aeroquip -10AN lines & fittings, carbon fiber ducts
RE-Speed oil filter pedestal adapter with -10AN outlet & gauge ports (passages ported by Gorilla RE)
Gorilla RE bell-mouth modified pick-up tube
Gorilla RE aluminum OMP oil supply block off plate
Earls -3AN hose/fittings for premix supply to Gorilla RE modified OEM oil metering pump
Afgmoto1978 black pre-mix tank in place of OEM vacuum canister
RE-Speed filler neck
Valvoline 10W-30 VR-1 motor oil
Idemitsu Racing rotary synthetic pre-mix
Jaz 1-pint breather can on Gorilla RE bracket with -4AN super stock hose & fittings to oil filler neck & rear irons unused oil drain
Instrumentation:
SPA oil pressure/temperature gauge
SPA water temperature/fuel pressure gauge
PLX egt gauge using Temp Rip sensors in turbo manifold
Innovative XD-19 wide band gauge and sensor with Gorilla RE aluminum heat sink
Defi D-gauge mechanical boost gauge
Electrical:
Odyssey PC925 battery in passenger side rear bin with Jegs aluminum battery tray mounted to Gorilla RE bracket that uses existing rear seat belt mounting points
Gorilla RE bracket for OEM battery fuse box
Phoenix Gold 200-A circuit breaker at battery
Phoenix Gold 1/0 positive & negative battery cables (both routed battery to starter, positive from starter to main fuse box)
Phoenix God 4-gauge ground cables at numerous points
OEM engine harness (unused wiring removed, re-wrapped with split loom, fusing tape, electrical tape, exposed portions wrapped with Thermo-Tec heat shield tape)
Sport Tuner 140-Amp alternator, cerma-chrome coated, blue painted stator
Wheels/Tires:
Volk SE37A 18x9.5 (F+45 /R+45 with 5mm spacer) powder coated black
Falken RT-615 265-35-19 F/R tires
Muteki black lug nuts
Suspension:
Aragosta 15-way adjustable dampers with 10.3/7.8-kg F/R springs
Suspension Techniques F/R sway bars
Improved Racing adjustable sway bar end links
Widefoot front sway bar mounts
RP/rx7.com trailing arms
M2 toe links
Cusco front strut tower brace
Drivetrain:
Atomic Rex manual steering rack
Exeddy D-core twin disk carbon clutch
RP/rx7.com stainless steel clutch line
Mazdaspeed short-throw shifter
Pettit 80-durometer differential mounts
NEO 75W90 synthetic gear oil in transmission & differential
Brakes:
Stop Tech front big brake kit with piston sized to match 99-spec rear & slotted rotors
99-spec OEM rear calipers with Precision 2-pc slotted rotors
Mazda 929 master cylinder
N-Tech front rotor backing plates
Stainless steel lines (Stop Tech front / rx7.com rear)
Motul RB-600 Brake fluid
Rotary 13B1 anodized blue rotor shaped brake/clutch fluid reservoir cap
Exterior:
Original Chaste White Paint
Shine replica Mazdaspeed front lip
Shine replica RE-A street diffuser
Front lip and diffuser sanded then coated with Dupli-color truck bed liner
OEM mud guards
Smoked front turn lamp housings
LED tail lights, marker lights, turn signals, reverse lights, license plate lights
20% rear / 50% side window tint
PIAA platinum series super white headlight bulbs
Interior:
Original 1994 unless otherwise mentioned
Mazdaspeed Type F seats recovered in BMW black leather
Momo Super Anatomic shift knob
Momo Monte Carlo 350mm steering wheel
Flyrx7 3-gauge 52mm center speaker gauge pod
Saab 3-gauge 52mm din panel
RE-Amemiya Steering column gauge pod
Redline.com black leather shift & parking brake boots
JDM armrest ashtray replacement
TNT rear hatch carpet
Misc:
Himni Racing stainless steel hardware throughout engine bay
Black powder coated brackets, hard water & brake lines throughout engine bay
Aba stainless steel hose clamps for air filter & wastegate lines
|