Rotary Car Club - View Single Post

***TitaniumTT*** · 12-27-2013, 10:59 AM

Hockey puck motor mounts would be over bdcs head

2x4 is where it at with him

I've been running the ES bushings foooooorrrrr.......16 years now I think? They all seem to be holding up pretty damn well given the type of miles that I put on the car. The MS pieces.... Not so well. Replaced the engine mounts a few times (mainly because the banzai cosmo motor mount adapters were not designed properly and the mounts were never loaded properly.) Once I built my own adapters the mounts seem to be holding up pretty well, they're actually strait now however they're still going to be need to be replaced but not with the same frequency as stock pieces. Even the front diff mount failed once on me.

Dave... Or in reality Kyle will be the one doing the work most likely... I would think it could be done in a day, I would check with Dave first though.

Using the serviceable S4 pieces doesn't change any of the geometry at all. You'll need a set of LCA's, a set of ball joints, a pair of the sway bar link brackets, and of course the end links as well. Last time I was there he had 2 Parts car FC's....

12-27-2013, 10:59 AM	#7
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	Hockey puck motor mounts would be over bdcs head 2x4 is where it at with him I've been running the ES bushings foooooorrrrr.......16 years now I think? They all seem to be holding up pretty damn well given the type of miles that I put on the car. The MS pieces.... Not so well. Replaced the engine mounts a few times (mainly because the banzai cosmo motor mount adapters were not designed properly and the mounts were never loaded properly.) Once I built my own adapters the mounts seem to be holding up pretty well, they're actually strait now however they're still going to be need to be replaced but not with the same frequency as stock pieces. Even the front diff mount failed once on me. Dave... Or in reality Kyle will be the one doing the work most likely... I would think it could be done in a day, I would check with Dave first though. Using the serviceable S4 pieces doesn't change any of the geometry at all. You'll need a set of LCA's, a set of ball joints, a pair of the sway bar link brackets, and of course the end links as well. Last time I was there he had 2 Parts car FC's.... __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-** Last edited by TitaniumTT; 12-27-2013 at 11:02 AM.