Rotary Car Club - View Single Post

imstillonjava · 08-19-2008, 02:31 AM

Can't forget the exterior...
I wanted to go all FEED. So eventually, I had pieced together a set of FEED cf hood, fenders, rear fenders (yet to go on the car permanently), and cf sidesteps.
I have the RE-Amemiya diffuser with the side generators still sitting in the study room garnering dust for the time being also.

And I ended up picking up a set of FEED halogen signals/fogs, tow hooks, and light covers.

I know theres also a brand spanking new set of Ganador side mirrors hiding somewhere in the garage along with the newer round tail lights.

And the parts along with the EVO-R projector headlights somehow turned my montego blue car half unpainted black.

And these CE28s which were put on just to see how flush it would sit with the rears....are actually just hanging out in the garage as is with not a mile on them

I rolled it onto the driveway about once so far! What a shame.

The seats in the car were torn (at least the driverside was terribly so, and it smelled funny as well!) So after much debate, I ended up going with a ASM Recaro TS-G bucket set.

And in the last couple months, I decided to finally install these delrin bushings I purchased, but in the course of installing those, getting the arms beadblasted and then clearcoating them, it was discovered more oem pillowballs, bushings, and rubber boots that were in need or replacement as well as the boots at the end of the tie rods.
And a start on the suspension got bigger and bigger. Everything was out, and I decided to upgrade the sway bars to a set of Feed sways I found for a good deal. And I decided to pair that up with a bunch of Super Now parts and a Makers7 tranny brace.
That'd be a great improvement to go along with the Noltec motor mounts that were installed earlier.

And then an opportunity for a Raceshop roll bar came by, and I didn't want to miss this chance again...

Ah, I forgot about this piece earlier. Polished and ceramic coated.

And last on my agenda for this post, but definitely not least. Something I wanted to replace the EVO-R headlights with because I wasn't satisfied with fitment or quality....a buddy helped me get a hold of these to go on the car.

Things that still need to go on now that are still packed away or enroute.
-RE-Amemiya VMIC
-Knightsports RF420 turbos.
-Apexi AST

Ah...might I add, newest part on the car is a red/pinkish r-magic oil cap...thats nifty and cool looking, but matches nothing like all getout!

...I can't wait to drive this thing again!

08-19-2008, 02:31 AM	#2
imstillonjava Rotary Fanatic Join Date: Mar 2008 Posts: 108 Rep Power: 18	Can't forget the exterior... I wanted to go all FEED. So eventually, I had pieced together a set of FEED cf hood, fenders, rear fenders (yet to go on the car permanently), and cf sidesteps. I have the RE-Amemiya diffuser with the side generators still sitting in the study room garnering dust for the time being also. And I ended up picking up a set of FEED halogen signals/fogs, tow hooks, and light covers. I know theres also a brand spanking new set of Ganador side mirrors hiding somewhere in the garage along with the newer round tail lights. And the parts along with the EVO-R projector headlights somehow turned my montego blue car half unpainted black. And these CE28s which were put on just to see how flush it would sit with the rears....are actually just hanging out in the garage as is with not a mile on them I rolled it onto the driveway about once so far! What a shame. The seats in the car were torn (at least the driverside was terribly so, and it smelled funny as well!) So after much debate, I ended up going with a ASM Recaro TS-G bucket set. And in the last couple months, I decided to finally install these delrin bushings I purchased, but in the course of installing those, getting the arms beadblasted and then clearcoating them, it was discovered more oem pillowballs, bushings, and rubber boots that were in need or replacement as well as the boots at the end of the tie rods. And a start on the suspension got bigger and bigger. Everything was out, and I decided to upgrade the sway bars to a set of Feed sways I found for a good deal. And I decided to pair that up with a bunch of Super Now parts and a Makers7 tranny brace. That'd be a great improvement to go along with the Noltec motor mounts that were installed earlier. And then an opportunity for a Raceshop roll bar came by, and I didn't want to miss this chance again... Ah, I forgot about this piece earlier. Polished and ceramic coated. And last on my agenda for this post, but definitely not least. Something I wanted to replace the EVO-R headlights with because I wasn't satisfied with fitment or quality....a buddy helped me get a hold of these to go on the car. Things that still need to go on now that are still packed away or enroute. -RE-Amemiya VMIC -Knightsports RF420 turbos. -Apexi AST Ah...might I add, newest part on the car is a red/pinkish r-magic oil cap...thats nifty and cool looking, but matches nothing like all getout! ...I can't wait to drive this thing again! Last edited by imstillonjava; 08-19-2008 at 02:36 AM.