Fuel bowl size? Making it bigger, IDA and DCO

sen2two · 04-01-2011, 04:04 PM

I have a 51 IDA Weber and I need to enlargen the fuel bowl area. I will be running E85 through it right now and down the road i will be running pure methanol (alcohol) through it. I am unsure how much I will need to add to the fuel bowl and what will the effects be of over enlargening it? Does this effect on how I set the float height? or anything else?

One other thing. I thought about swapping to the larger factory 55 dco (side draft) weber, but I am unsure of how to make that bowl larger. I don't really see how it could be done on a side draft Weber. Maybe adding a separate reservoir off the side of the block above the Webers and letting it gravity feed into the bowl with large fuel line?

Ant help here would be great!

TheDriver216 · 04-01-2011, 09:34 PM

i dont think a sidedraft is possible... but the downdrafts i know can be and a company makes some huge carbs already

visually this should help for the ida

http://www.geersengineering.com/Terminator%20Carbs.htm

sen2two · 04-02-2011, 10:49 AM

Yeah, those are the carbs I pan on getting in the future. But for right now I'm going to use my 51's because it's what I have.

I know how to enlargen the bowl, I'm really looking for how much fluid should it hold? add 10%, 20%, or more fluid volume?

730RWHP12A · 04-07-2011, 07:44 PM

here is some mods i just did to a customer's IDA
float level should not need to change when enlarging the float bowl.

730RWHP12A · 04-07-2011, 07:47 PM

you need one of these massive needle valves and a proper fuel inlet too

04-01-2011, 04:04 PM	#1
sen2two KTEC Join Date: Jan 2009 Posts: 642 Rep Power: 0	Fuel bowl size? Making it bigger, IDA and DCO I have a 51 IDA Weber and I need to enlargen the fuel bowl area. I will be running E85 through it right now and down the road i will be running pure methanol (alcohol) through it. I am unsure how much I will need to add to the fuel bowl and what will the effects be of over enlargening it? Does this effect on how I set the float height? or anything else? One other thing. I thought about swapping to the larger factory 55 dco (side draft) weber, but I am unsure of how to make that bowl larger. I don't really see how it could be done on a side draft Weber. Maybe adding a separate reservoir off the side of the block above the Webers and letting it gravity feed into the bowl with large fuel line? Ant help here would be great! __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

04-01-2011, 09:34 PM	#2
TheDriver216 Rotary Fanatic Join Date: Feb 2008 Location: Cleveland, Ohio Posts: 159 Rep Power: 18	i dont think a sidedraft is possible... but the downdrafts i know can be and a company makes some huge carbs already visually this should help for the ida http://www.geersengineering.com/Terminator%20Carbs.htm Last edited by TheDriver216; 04-01-2011 at 09:38 PM.

04-02-2011, 10:49 AM	#3
sen2two KTEC Join Date: Jan 2009 Posts: 642 Rep Power: 0	Yeah, those are the carbs I pan on getting in the future. But for right now I'm going to use my 51's because it's what I have. I know how to enlargen the bowl, I'm really looking for how much fluid should it hold? add 10%, 20%, or more fluid volume? __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode