When idler pulley bearings fail!!! - Page 2

Uncle Hungry · 07-28-2009, 08:03 AM

I really like this design. I personally have the pineapple idler and there are a few differences. Both are over engineered but in different ways. The pineapple pulley itself is a beautiful piece using not one but 2 isk (I think) bearings. This is the better of the two by far in this department imo. The Tweakit bracket itself it WAY beefier and puts the pulley in a less obtrusive location for some big single turbo guys, but leads to slightly less water pump pulley contact. I think a new piece with a Pineapple style pulley and a location closer to the Tweakit design would be the best of both worlds. Just my opinion, which nobody asked for lol.

imstillonjava · 11-30-2009, 04:45 AM

curious, since i have this same idler pulley kit... mcmaster-carr has discontinued carrying the 2349k471, and they do not have an alternative bearing with those dimensions that meet the rpm requirements. Do you know if the honda bearing you cited meets the rpm rating criteria? i wasn't able to dig any info up on it.

sbrian2 · 11-30-2009, 11:08 AM

There is a reason they discontinued the bearing, it was over rated. :-/

We now use a NSK non-contact double sealed bearing. The part number is 6002 VV and is rated at 24,000 RPM.

imstillonjava · 11-30-2009, 11:21 AM

thanks brian. pmed..

sbrian2 · 11-30-2009, 12:18 PM

Quote:

Originally Posted by imstillonjava

thanks brian. pmed..

Yes, we did a voluntary recall a while back and emails were sent to all that purchased from the first few groups, but it is possible we missed a few people. Just send the pulley back to us and we will swap out the bearing and send it back. The address is:

Tweakit Racing
531 Huntley Industrial Blvd.
Smyrna, TN 37167

JHew84 · 12-04-2009, 11:21 AM

Quote:

Originally Posted by sbrian2

Yes, we did a voluntary recall a while back and emails were sent to all that purchased from the first few groups, but it is possible we missed a few people. Just send the pulley back to us and we will swap out the bearing and send it back. The address is:

Tweakit Racing
531 Huntley Industrial Blvd.
Smyrna, TN 37167

I am pretty sure I was in on the first GB but I'm not 100% sure and can't find the thread, I didn't get an email but if you could check to see if I'm on the list that would be cool, name is James Hewson. Mine did ship out a little later because I changed my order towards the end of the GB to a single turbo pulley, dunno if that will make a difference.

I haven't installed the bearing yet but will likely be doing it over the winter, I'll see if I can't dig it out of my parts box and see if it's the older bearing.

Glad I randomly decided to see the bearing carnage in this thread!

.

Tech B · 12-11-2009, 09:40 PM

Good to hear you guys stand behind your stuff.

Brent · 12-11-2009, 09:48 PM

There is def. something to be said about TweakIt as a vendor. Dan and Brian are building my yellow car. There aren't many people I trust to work on my stuff, they are one of a few that I don't give a second thought about when it comes to that.

07-28-2009, 08:03 AM	#16
Uncle Hungry The Newbie Join Date: Feb 2008 Location: 600' up Posts: 20 Rep Power: 0	I really like this design. I personally have the pineapple idler and there are a few differences. Both are over engineered but in different ways. The pineapple pulley itself is a beautiful piece using not one but 2 isk (I think) bearings. This is the better of the two by far in this department imo. The Tweakit bracket itself it WAY beefier and puts the pulley in a less obtrusive location for some big single turbo guys, but leads to slightly less water pump pulley contact. I think a new piece with a Pineapple style pulley and a location closer to the Tweakit design would be the best of both worlds. Just my opinion, which nobody asked for lol. __________________ www.full-race.com Anything else is half-fast

11-30-2009, 11:08 AM	#18
sbrian2 Rotary Wannabee Join Date: Mar 2008 Location: M'boro TN Posts: 50 Rep Power: 18	There is a reason they discontinued the bearing, it was over rated. :-/ We now use a NSK non-contact double sealed bearing. The part number is 6002 VV and is rated at 24,000 RPM. __________________ -Brian '95 Mazda Miata R package '90 Mazda Miata turbo '06 Chevrolet Trailblazer SS '01 BMW 325Ci '91 Honda CRX hf

11-30-2009, 11:21 AM	#19
imstillonjava Rotary Fanatic Join Date: Mar 2008 Posts: 108 Rep Power: 18	thanks brian. pmed.. Last edited by imstillonjava; 11-30-2009 at 12:14 PM.

12-11-2009, 09:48 PM	#23
Brent Sua Sponte Join Date: Feb 2008 Location: Killeen, TX Posts: 839 Rep Power: 18	There is def. something to be said about TweakIt as a vendor. Dan and Brian are building my yellow car. There aren't many people I trust to work on my stuff, they are one of a few that I don't give a second thought about when it comes to that. __________________ Road Atlanta August 2011 NASA TT 1:33 http://www.youtube.com/watch?v=IFY00PAK_Ps Traqmate's video of my car from the 2011 UTCC at VIR http://www.youtube.com/watch?v=2Zcn6...layer_embedded Video of Yellow LS1 FD at NASA TT at VIR http://www.youtube.com/watch?v=e6k0lJkcwrM

11-30-2009, 04:45 AM	#17
imstillonjava Rotary Fanatic Join Date: Mar 2008 Posts: 108 Rep Power: 18	curious, since i have this same idler pulley kit... mcmaster-carr has discontinued carrying the 2349k471, and they do not have an alternative bearing with those dimensions that meet the rpm requirements. Do you know if the honda bearing you cited meets the rpm rating criteria? i wasn't able to dig any info up on it.

12-11-2009, 09:40 PM	#22
Tech B The Newbie Join Date: Dec 2009 Posts: 20 Rep Power: 0	Good to hear you guys stand behind your stuff.