Digi Dash Mount Fab - Page 3

vex · 03-03-2011, 09:48 PM

It's all good. The Faux leather is for the mold over foam B. The turn signal cut out is modeled from the stock green covers. I'm open to alternate suggestions in this matter, though I do not like the thought of just having single LED's for indicators. And yes, I'm still using the center warning cluster.

Look what I found:
http://www.signal-construct.de/image...ffgehaeuse.pdf

Those should make things easier. Just have to find a place that sells 'em.

chibikougan · 03-03-2011, 10:48 PM

Nice! Those will make things much simpler.

vex · 03-03-2011, 10:50 PM

But I can't find anyone who sells 'em. :/

vex · 03-04-2011, 10:41 AM

So this might be a silly question: Will I still need to deal with the "Shift Up" light from the stock dash, or will it be disabled when I switch to the standalone? My gut says it will be disabled, but I'd rather make sure than guess (and I'm feeling kind of lazy).

tweiss3 · 03-04-2011, 10:46 AM

Unless you create an output from the standalone to be a shift up light, its not going to exist. In fact, that must be an S4 thing, cause my S5 doesn't have one that i know of, just the buzzer

vex · 03-04-2011, 11:04 AM

unless I'm much mistaken the Digi dash will have shift and warning lights built in and used by the ECU automatically. I'm just concerned that I may have a live wire back there causing havoc whenever I get into the higher RPM band.

tweiss3 · 03-04-2011, 11:11 AM

why would you have a loose wire? Aren't you rebuilding the harness? If you have to, tape it off.

vex · 03-04-2011, 11:18 AM

I think we're missing each other here. There's a plethora of wires coming into the stock dash. Among which include the Brights indication, Blinkers, and the Shift up light. Rather than remove the entire dash unit I was planning on just pulling the wires that I need (blinkers and brights indication). My question however is does the stock setup pull the voltage for the shift up from the stock ECU or is it pulling it from a secondary computer?

tweiss3 · 03-04-2011, 11:21 AM

ooooooohhhh, i thought you were doing a TTT and pulling the whole harness. let me grab the wiring diagram here in a minute and check it out for you

tweiss3 · 03-04-2011, 11:22 AM

what year is yours?

vex · 03-04-2011, 11:27 AM

S4:86-87.5

tweiss3 · 03-04-2011, 11:39 AM

On the 88 wire diagram i see, its just looped in with the speed sensor/tack

vex · 03-04-2011, 01:24 PM

Okay, cool.

I've been thinking of the lenses and it might be pretty cool to use a light bar or elongated LED's if I can't source a proper arrow lens (I sent out a few emails, waiting to hear back). Thoughts?

I'm trying to avoid the standard circular LED's.

tweiss3 · 03-04-2011, 01:39 PM

i've got nothin for ya, sorry

chibikougan · 03-04-2011, 04:32 PM

I am searching us suppliers at the moment but they all have millions of LEDs

Might try these guys http://www.kingbright-europe.de/index_fr.htm

^^ These guys have a Dot matrix you could light in an arrow in any color for that race look..

03-03-2011, 09:48 PM	#31
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	It's all good. The Faux leather is for the mold over foam B. The turn signal cut out is modeled from the stock green covers. I'm open to alternate suggestions in this matter, though I do not like the thought of just having single LED's for indicators. And yes, I'm still using the center warning cluster. Look what I found: http://www.signal-construct.de/image...ffgehaeuse.pdf Those should make things easier. Just have to find a place that sells 'em. __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group Last edited by vex; 03-03-2011 at 10:10 PM. Reason: ARROW SHAPED LED!

03-03-2011, 10:50 PM	#33
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	But I can't find anyone who sells 'em. :/ __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 10:41 AM	#34
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	So this might be a silly question: Will I still need to deal with the "Shift Up" light from the stock dash, or will it be disabled when I switch to the standalone? My gut says it will be disabled, but I'd rather make sure than guess (and I'm feeling kind of lazy). __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 10:46 AM	#35
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	Unless you create an output from the standalone to be a shift up light, its not going to exist. In fact, that must be an S4 thing, cause my S5 doesn't have one that i know of, just the buzzer __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles

03-04-2011, 11:04 AM	#36
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	unless I'm much mistaken the Digi dash will have shift and warning lights built in and used by the ECU automatically. I'm just concerned that I may have a live wire back there causing havoc whenever I get into the higher RPM band. __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 11:11 AM	#37
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	why would you have a loose wire? Aren't you rebuilding the harness? If you have to, tape it off. __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles

03-04-2011, 11:18 AM	#38
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	I think we're missing each other here. There's a plethora of wires coming into the stock dash. Among which include the Brights indication, Blinkers, and the Shift up light. Rather than remove the entire dash unit I was planning on just pulling the wires that I need (blinkers and brights indication). My question however is does the stock setup pull the voltage for the shift up from the stock ECU or is it pulling it from a secondary computer? __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 11:21 AM	#39
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	ooooooohhhh, i thought you were doing a TTT and pulling the whole harness. let me grab the wiring diagram here in a minute and check it out for you __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles

03-04-2011, 11:22 AM	#40
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	what year is yours? __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles

03-04-2011, 11:27 AM	#41
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	S4:86-87.5 __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 11:39 AM	#42
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	On the 88 wire diagram i see, its just looped in with the speed sensor/tack __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles

03-04-2011, 01:24 PM	#43
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. Posts: 2,113 Rep Power: 20	Okay, cool. I've been thinking of the lenses and it might be pretty cool to use a light bar or elongated LED's if I can't source a proper arrow lens (I sent out a few emails, waiting to hear back). Thoughts? I'm trying to avoid the standard circular LED's. __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

03-04-2011, 01:39 PM	#44
tweiss3 Mazda Lover Join Date: Aug 2010 Location: Akron, Ohio Posts: 319 Rep Power: 16	i've got nothin for ya, sorry __________________ 2004 Mazda6 V6 5-spd - still waiting on money for a motor 1991 Mazda RX7 NA 5-spd - my new DD with 145,000 miles