Delorto 49 Ida?

Mateepay · 11-11-2010, 03:06 AM

So I have been slowly installing my delorto these past few days and I'm moderately confused on what to do with a few things...

I have the fuel return line? And nowhere to install it

The vacum advance for distributer

And i'm not sure what to do with the third cable running along with the choke and accelerator cable

Any info would be greatly appreciated

Mateepay · 11-11-2010, 03:07 AM

48ida

t_g_farrell · 11-11-2010, 07:27 AM

Its a 48 DHLA (sidedraft).

If you don't have a return regulator then just cap the return for now. I run
the vent line into the middle iron nipple and have a PCV valve attached to the
oil filler nipple with vacuum on that. Don't run vacuum advance since I improved
my ignition.

Was that third cable for cruise control? Not sure what you want to do with
that.

Mateepay · 11-11-2010, 11:59 AM

The only thing I can come up with is a hot start motor assist or a ac component
what's the esiest way to update the vaccume advance

sen2two · 11-11-2010, 12:33 PM

Make sure your mounting it the correct way. If you mount a side draft in a down draft position, it will not work. And vica versa...

Mateepay · 11-11-2010, 07:12 PM

i mounted it the way i removed it off of my parts car im just a little confused about what is a must to keep for correct operation and which of the cluster of cables and lines i can chuunk

t_g_farrell · 11-12-2010, 10:16 AM

If you throw some pics up we might be able to help better.

Mateepay · 11-12-2010, 12:46 PM

Img_0427.jpg

Mateepay · 11-12-2010, 12:48 PM

Well that didn't work haven't been using the forum long enough to figure out how to import pics T_T

sen2two · 11-12-2010, 03:04 PM

Use photo bucket or something similar. It's usually easier that way than to load pics directly to the forum...

Mateepay · 11-12-2010, 07:29 PM

DOES ANYONE ON HERE KNOW WHAT FILTER SIZE WILL FIT THIS RACING BEAT INTAKE COVER?? DELLORTO DHLA 48IDA IM HAVING NO LUCK T-T

Mateepay · 11-12-2010, 07:57 PM

this is the piece idk what to do with do i need this to run the carb??

11-11-2010, 03:06 AM	#1
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	Delorto 49 Ida? So I have been slowly installing my delorto these past few days and I'm moderately confused on what to do with a few things... I have the fuel return line? And nowhere to install it The vacum advance for distributer And i'm not sure what to do with the third cable running along with the choke and accelerator cable Any info would be greatly appreciated

11-11-2010, 07:27 AM	#3
t_g_farrell Waffles - hmmm good Join Date: Aug 2008 Location: Huntersville, NC Posts: 757 Rep Power: 0	Its a 48 DHLA (sidedraft). If you don't have a return regulator then just cap the return for now. I run the vent line into the middle iron nipple and have a PCV valve attached to the oil filler nipple with vacuum on that. Don't run vacuum advance since I improved my ignition. Was that third cable for cruise control? Not sure what you want to do with that. __________________ 1980 GS stockport, Fat Nikki, RB Dual Facetfuel pumps, Holley regulator, RB Street port exhaust, 2GDFIS, MR2 MK I electric fans, 2G strut bar, relayed fans, lights and fuel pump, LEDs Project Fat Nikki Budget 12A rebuild Video setup < $30.00

11-11-2010, 12:33 PM	#5
sen2two KTEC Join Date: Jan 2009 Posts: 642 Rep Power: 0	Make sure your mounting it the correct way. If you mount a side draft in a down draft position, it will not work. And vica versa... __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

11-12-2010, 10:16 AM	#7
t_g_farrell Waffles - hmmm good Join Date: Aug 2008 Location: Huntersville, NC Posts: 757 Rep Power: 0	If you throw some pics up we might be able to help better. __________________ 1980 GS stockport, Fat Nikki, RB Dual Facetfuel pumps, Holley regulator, RB Street port exhaust, 2GDFIS, MR2 MK I electric fans, 2G strut bar, relayed fans, lights and fuel pump, LEDs Project Fat Nikki Budget 12A rebuild Video setup < $30.00

11-12-2010, 03:04 PM	#10
sen2two KTEC Join Date: Jan 2009 Posts: 642 Rep Power: 0	Use photo bucket or something similar. It's usually easier that way than to load pics directly to the forum... __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

11-11-2010, 03:07 AM	#2
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	48ida

11-11-2010, 11:59 AM	#4
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	The only thing I can come up with is a hot start motor assist or a ac component what's the esiest way to update the vaccume advance

11-11-2010, 07:12 PM	#6
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	i mounted it the way i removed it off of my parts car im just a little confused about what is a must to keep for correct operation and which of the cluster of cables and lines i can chuunk

11-12-2010, 12:46 PM	#8
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	Img_0427.jpg

11-12-2010, 12:48 PM	#9
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	Well that didn't work haven't been using the forum long enough to figure out how to import pics T_T

11-12-2010, 07:29 PM	#11
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	DOES ANYONE ON HERE KNOW WHAT FILTER SIZE WILL FIT THIS RACING BEAT INTAKE COVER?? DELLORTO DHLA 48IDA IM HAVING NO LUCK T-T Last edited by Mateepay; 11-12-2010 at 10:02 PM.

11-12-2010, 07:57 PM	#12
Mateepay Rotary Fan in Training Join Date: Jun 2010 Location: tulsa, ok Posts: 71 Rep Power: 16	this is the piece idk what to do with do i need this to run the carb??

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode