Parting Bridge Port Single turbo Touring 93

[Fritz Flynn]

Any FD MISC parts you need just send me a PM but as usual I'll post the good stuff 1st. Best offers are always welcome but because these parts are in excellent condition prices are pretty firm.

LESS THAN 2K MILES ON MOST IF NOT ALL THESE PARTS

RX7Store GT40R turbo kit $2250

RX7Store Ultimate Fuel Kit(1000cc primaries, 1600cc secodaries, Aeromotive A1000 FPR w/ liquid filled gauge, KG Parts primary rail and RX7Store secondary rail) $600

RX7Store non-resonated SS midpipe $100

RX7Store block off plates $50

Twin walbro fuel pump setup (done by PFS) $250

K&N 4" air filter $50

Greddy 2 row FMIC (vspec) $650

Greddy TB Elbow $95

Greddy Type S BOV $125

Apexi GT Spec Exhaust $400

HKS twin power 300

Short block Bridge Ported Engine built by PFS. This would cost you about 4k plus your core and that's if everything you gave him was good. $3000 OR With Ground Zero oil pan $3300

Ground Zero Oil Pan $400 (like new)

A-Spec motor mounts $150

GM 3bar map sensor $50

Exedy Twin Plate Clutch $1100

B&M short shifter $125

Innovative Lm1 W/B standalone o2 w/ gauge $300

Stainless OMP lines $90

Magnecor 10mm wires $65

Fluidyne Radiator $300

Greddy Profec B(Original) $225

HKS Turbo Timer $45

Gotham Racing Turbo Blanket $120 (like new)

Thanks,
Fritz

[dudemaaan]

are you just parting out the engine or the whole car?

[dregg100]

pmed

[Fritz Flynn]

dregg100 I'll check out the tail light for you asap and send you a PM

This car has a salvage title so there's no reason to sell it as a roller. It will be parted down the shell.

Thanks,
Fritz

[Mirage]

Will the twin power come with all the necessary wiring/harness etc

[charlies7]

So who bought that PFS MB beauty..

[David Jerome]

Originally Posted by charlies7

So who bought that PFS MB beauty..

I figured, Fritz, Allrotor, you or myself would have bought it eventually. That is one hell of a car to part out. Fritz, tell me you at least did a couple 3rd and 4th gear pulls before the partout

For those who dont know, these parts are all top notch stuff and came off a very impressive car.

David

[Fritz Flynn]

There wasn't enough race gas in it so I never boosted it.

Just revving it will put a big grin on your face.

Originally Posted by David Jerome

I figured, Fritz, Allrotor, you or myself would have bought it eventually. That is one hell of a car to part out. Fritz, tell me you at least did a couple 3rd and 4th gear pulls before the partout

For those who dont know, these parts are all top notch stuff and came off a very impressive car.

David

[Brent]

fritz, I'll take the twin power and 3 bar if the twin power comes with the harness. Just PM me the price shipped and I'll paypal. Thanks.

Brent

[TRISPEEDFD3S]

SO how well would this engine perform on the street? HAHA I never had anything other than my stock ports...2mm or 3mm seals? Mileage? Also, is that price shipped Fritz?

[sk8world]

So someone finally bought this car! To bad to part a 600rwhp setup.. Has the motor been tested? What rotors are in it? Have any detail on the build up? What parts new? balanced?

[Fritz Flynn]

Originally Posted by sk8world

So someone finally bought this car! To bad to part a 600rwhp setup.. Has the motor been tested? What rotors are in it? Have any detail on the build up? What parts new? balanced?

Parts replaced:
rotor bearings
seals
springs
water seals
etc....

All parts are well within spec. I talked to Ray at length about it before buying the car.

obviously a well built engine

Oh and of course it was balanced.

I think 600 plus rwhp is a pretty good test. Current health: It's a bridge port that's tuned on c16 has 10.5 race plugs in it and it starts, idles and revs freely.

[Fritz Flynn]

Parts sold:
Greddy elbow
Fuel pumps
Clutch
Short shifter
Motor mounts

[Fritz Flynn]

More Parts sold:
Turbo kit
HKS twin power
Oil pan
GT spec catback
Ultimate fuel kit

Price lowered on the fluidyne 275 shipped

Thanks,
Fritz

[IR Performance]

Better off parted. Salvaged cars are worthless. Nice prices for the parts