New Coil Relocation Bracket - Feeler - Page 4

fire85gslse · 07-10-2009, 07:09 AM

looks good. Only difference than mine as seem in the first pictures is that I put mine on a slight angle. I did not want water to sit on top of the coils and give it a chance to mess with my connectors.
This way gravity allows it to roll off.

Monkman33 · 09-21-2009, 12:58 PM

Are these still available? I have an FD with a T2 Coil.

Garfinkles Motor Works · 09-23-2009, 07:41 PM

Yes I have several for stock coils and for stock trailing and sec gen leading .Ready to ship.

airboarder69 · 11-20-2009, 07:35 PM

I wanted to see if you still have any brackets for the third gen ('93 RX7 FD) stock T1 T2 coil packs. If so I'd love to get my hands on one. If you do still have one can you request a payment through paypal. My paypal ID is airboarder69@yahoo.com. Anyways let me know and when I get the payment request I'll approve it ASAP so you can ship it out. Thanks man.

-TC

neit_jnf · 01-22-2010, 03:27 PM

I want one for stock FD coils! any available?

Garfinkles Motor Works · 01-22-2010, 09:08 PM

Sorry they are sold out. I have two for using the 2nd gen leading coil . I will make more of both when I have time . I will PM you but it may be a few days as I am behind schedule .

Prodigy · 04-19-2010, 01:32 PM

These do work with a RHD, except the spacing is quite limited due to a fluid hardline that runs right through that area, my Bracket is almost sitting on the subframe, and has a slight angle to it. (angled towards the rear of the car) its the only way it would fit.

But great build quality, Garfinkle makes some amazing products...

J.

Garfinkles Motor Works · 04-23-2010, 07:36 AM

Coil relocation plates are ready to ship,both types .4-23-2010

AzEKnightz · 11-10-2010, 01:45 PM

Still have the relocation plates for the FD LHD?

-AzEKnightz

Garfinkles Motor Works · 11-13-2010, 07:31 AM

Yes I have some ready to ship .

FD3sAutobot · 04-04-2011, 10:57 AM

Sent you a PM about these.

Garfinkles Motor Works · 04-07-2011, 01:25 AM

Shipped it out 4-6-11 morning Thank You David

neit_jnf · 04-07-2011, 04:38 PM

I got one FS with a 2nd gen coil. I'm not going to be using it, anyone want it?

LongRX7 · 04-08-2011, 05:04 PM

Do you make new plug wires for these too? and how much?

Garfinkles Motor Works · 04-11-2011, 10:52 PM

I was making plug wires with 40 ohm MSD 8mm wire but I ran out .Sorry ,just recut your wires, either old or new.

07-10-2009, 07:09 AM	#46
fire85gslse RCC Addict Join Date: Feb 2008 Location: Middle TN Posts: 1,029 Rep Power: 19	looks good. Only difference than mine as seem in the first pictures is that I put mine on a slight angle. I did not want water to sit on top of the coils and give it a chance to mess with my connectors. This way gravity allows it to roll off. __________________ I own A few Rotaries and Yes, I have a rotary problem. (SELLING OFF All my parts) 79SA(Respeed Car),93 FD (tweakit)

11-20-2009, 07:35 PM	#49
airboarder69 Project X Join Date: Nov 2009 Location: SoDak Posts: 6 Rep Power: 0	Coil relocation bracket I wanted to see if you still have any brackets for the third gen ('93 RX7 FD) stock T1 T2 coil packs. If so I'd love to get my hands on one. If you do still have one can you request a payment through paypal. My paypal ID is airboarder69@yahoo.com. Anyways let me know and when I get the payment request I'll approve it ASAP so you can ship it out. Thanks man. -TC

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-21-2009, 12:58 PM	#47
Monkman33 Still Building my FD Join Date: Jun 2009 Location: Pasco, WA Posts: 255 Rep Power: 17	Are these still available? I have an FD with a T2 Coil.

09-23-2009, 07:41 PM	#48
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	Yes I have several for stock coils and for stock trailing and sec gen leading .Ready to ship.

01-22-2010, 03:27 PM	#50
neit_jnf Boricua! Join Date: Jul 2008 Location: Puerto Rico Posts: 99 Rep Power: 18	I want one for stock FD coils! any available?

01-22-2010, 09:08 PM	#51
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	Sorry they are sold out. I have two for using the 2nd gen leading coil . I will make more of both when I have time . I will PM you but it may be a few days as I am behind schedule .

04-23-2010, 07:36 AM	#53
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	Coil relocation plates are ready to ship,both types .4-23-2010

11-10-2010, 01:45 PM	#54
AzEKnightz ZooM ZooM!! Join Date: Jun 2008 Location: SF, CA Posts: 90 Rep Power: 18	Still have the relocation plates for the FD LHD? -AzEKnightz

11-13-2010, 07:31 AM	#55
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	Yes I have some ready to ship .

04-04-2011, 10:57 AM	#56
FD3sAutobot Rotary Fan in Training Join Date: Sep 2008 Location: Durham,NC/ Ft Campbell, KY/Afghanistan Posts: 57 Rep Power: 18	Sent you a PM about these.

04-07-2011, 01:25 AM	#57
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	Shipped it out 4-6-11 morning Thank You David

04-07-2011, 04:38 PM	#58
neit_jnf Boricua! Join Date: Jul 2008 Location: Puerto Rico Posts: 99 Rep Power: 18	I got one FS with a 2nd gen coil. I'm not going to be using it, anyone want it?

04-08-2011, 05:04 PM	#59
LongRX7 The Newbie Join Date: Apr 2011 Posts: 7 Rep Power: 0	Do you make new plug wires for these too? and how much?

04-11-2011, 10:52 PM	#60
Garfinkles Motor Works RCC Contributor Join Date: Mar 2008 Posts: 535 Rep Power: 18	I was making plug wires with 40 ohm MSD 8mm wire but I ran out .Sorry ,just recut your wires, either old or new.