Wire location? - Page 2

Rx-7fetish · 02-13-2010, 10:49 AM

I got the car runnin and the damn water pump gave out!!!!!!!!!!!!!! It was fine last night then this mornin i went to go over it and noticed the coolant was low, i was like wtf, please please dont be a blown seal, so i went to add more before i started to see what was going on and as soon as i started to add water it came streaming out of the pump seep hole. I wanted to beat something!

Ender · 02-14-2010, 06:23 AM

Well... would you rather it had blown instead? lol At least a water pump is easy and relatively cheap on these

***TitaniumTT*** · 02-14-2010, 09:14 AM

Quote:

Originally Posted by Ender

OMG someone killed it with FIRE! If that were my car this would encourage me to remove the ACV altogether.

Fuck that, if this were my car I'd have the whole harness out, stripped back, and all the uneccesary wires removed and all the others inspected. Little shit like that leads to BIG problems in the future.

Quote:

Originally Posted by Ender

Well... would you rather it had blown instead? lol At least a water pump is easy and relatively cheap on these

Yup, easiest waterpump I can think of on any car that I've ever worked on. If you're doing the wp though, replace the housing/iron seal as well. Chances are good that the seal will break when you pull the WP.

Rx-7fetish · 02-14-2010, 11:56 AM

Pump replaced. Alls good. I still need to know what goes to that vac nipple. Someone please go look at there car and trace it back for me. PLEASE!!!

Dzire · 02-15-2010, 06:26 PM

This is What I have on my car
http://banzai-racing.com/store/FC_block_off_plates.html

Rx-7fetish · 02-15-2010, 11:18 PM

come on people i know all about block off plates and removal. so i take the acv off and cap the lines. now i still have the same problem because that line doest even go to the acv and the other end will still be leaking. will someone please just tell me where the line that goes on that nipple goes so i can go block it. im broke as hell work at a grocery store and go to college. i cant afford block off plates right now. cant someone just tell me where it goes i didnt think it would be this hard to get an answer.

Dzire · 02-15-2010, 06:37 PM

The how too
http://www.rotaryresurrection.com/2n...s_removal.html

Dzire · 02-15-2010, 11:55 PM

http://foxed.ca/rx7manual/manuals/19...TEMS_TURBO.pdf
here is a link to answer all your questions I honestly don't remember where it go every second generation RX 7 that I have own I ripped out all the rat's nest

Ender · 02-15-2010, 11:55 PM

Look around your engine for open sources. Check your EGR, your twin scroll solenoid, your vacuum solenoid rack...

Rx-7fetish · 02-16-2010, 02:03 AM

I don't have the twin scroll anymore but the lines to that are capped off already. I have looked and looked but can't find it that's why I asked. I understand those of you who have removed your emissions don't remember and can't go look lol but someone somewhere on this forum has to have there stock emissions intact still.

Ender · 02-16-2010, 09:29 AM

This is a simple option, especially if you have a compressor:
http://www.boostpro.net/prodtester.html

I got a gauged single pop with the male compressor adapter. No, it's not free, but believe me it's worth $25.

Rx-7fetish · 02-16-2010, 10:58 AM

I build boost just fine but my idle sucks. Don't worry about it guys I'll figure it out myself. I'll have to wait till summer to go to the car shows and look at someone elses car.

Ender · 02-16-2010, 01:56 PM

Quote:

Originally Posted by Rx-7fetish

I build boost just fine but my idle sucks. Don't worry about it guys I'll figure it out myself. I'll have to wait till summer to go to the car shows and look at someone elses car.

Boost leaks are usually also vacuum leaks. Idle can suffer greatly from small leaks that you wouldn't notice under boost. They call it a boost leak tester, and yes it allows you to check for leaks by pressurizing the intake, but like I said, boost leaks are usually vacuum leaks as well. But if you want to wait until summer be my guest.

02-15-2010, 06:26 PM	#5
Dzire Rotary Fanatic Join Date: Apr 2008 Location: B,ham AL/Hollywood FL Posts: 151 Rep Power: 18	This is What I have on my car http://banzai-racing.com/store/FC_block_off_plates.html __________________ RX8 2004 GT RX7 1988 TII Last edited by Dzire; 02-15-2010 at 06:33 PM.

02-15-2010, 06:37 PM	#7
Dzire Rotary Fanatic Join Date: Apr 2008 Location: B,ham AL/Hollywood FL Posts: 151 Rep Power: 18	The how too http://www.rotaryresurrection.com/2n...s_removal.html __________________ RX8 2004 GT RX7 1988 TII

02-15-2010, 11:55 PM	#8
Dzire Rotary Fanatic Join Date: Apr 2008 Location: B,ham AL/Hollywood FL Posts: 151 Rep Power: 18	http://foxed.ca/rx7manual/manuals/19...TEMS_TURBO.pdf here is a link to answer all your questions I honestly don't remember where it go every second generation RX 7 that I have own I ripped out all the rat's nest __________________ RX8 2004 GT RX7 1988 TII

02-13-2010, 10:49 AM	#1
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor Posts: 211 Rep Power: 0	I got the car runnin and the damn water pump gave out!!!!!!!!!!!!!! It was fine last night then this mornin i went to go over it and noticed the coolant was low, i was like wtf, please please dont be a blown seal, so i went to add more before i started to see what was going on and as soon as i started to add water it came streaming out of the pump seep hole. I wanted to beat something!

02-14-2010, 11:56 AM	#4
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor Posts: 211 Rep Power: 0	Pump replaced. Alls good. I still need to know what goes to that vac nipple. Someone please go look at there car and trace it back for me. PLEASE!!!

02-15-2010, 11:18 PM	#6
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor Posts: 211 Rep Power: 0	come on people i know all about block off plates and removal. so i take the acv off and cap the lines. now i still have the same problem because that line doest even go to the acv and the other end will still be leaking. will someone please just tell me where the line that goes on that nipple goes so i can go block it. im broke as hell work at a grocery store and go to college. i cant afford block off plates right now. cant someone just tell me where it goes i didnt think it would be this hard to get an answer.

02-16-2010, 02:03 AM	#10
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor Posts: 211 Rep Power: 0	I don't have the twin scroll anymore but the lines to that are capped off already. I have looked and looked but can't find it that's why I asked. I understand those of you who have removed your emissions don't remember and can't go look lol but someone somewhere on this forum has to have there stock emissions intact still.

02-16-2010, 10:58 AM	#12
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor Posts: 211 Rep Power: 0	I build boost just fine but my idle sucks. Don't worry about it guys I'll figure it out myself. I'll have to wait till summer to go to the car shows and look at someone elses car.