Diary of a Madman; TitaniumTT's see you @ DGRRXI RE-REbuild

[helghast7]

lol brians like chuck norris, lets make some t shirts haha

[TitaniumTT]

Originally Posted by EJayCe996

You're TTT...
1. You're always right
2. Fucking always.
3. You never sleep, you just wait with your eyes closed.
4. Everything works
5. Fucking always.
6. You're not an angry person.
*7. You WILL stab someone.

what?@!?!?

#3 maybe my favorite

Originally Posted by helghast7

lol brians like chuck norris, lets make some t shirts haha

haahahaah

[helghast7]

btw the dashpot thingy is the piece on the tb that connects to the throttle linkage, it has that movable tongue looking thing that helps slow the plates on a decel

well my tongue thing is not moving...so i need a new one

i wish i had a pic, it would make way more sense

[vex]

lol. Brian, how are you checking your fuel level (via dash. I assume you're just going to use the motec sensor for the signal)? I'm trying to figure out mapping for my car... and I think I have it nailed, but want to see what you do.

[TitaniumTT]

Originally Posted by helghast7

btw the dashpot thingy is the piece on the tb that connects to the throttle linkage, it has that movable tongue looking thing that helps slow the plates on a decel

well my tongue thing is not moving...so i need a new one

i wish i had a pic, it would make way more sense

Negatory, I know exactely what it is. Would the one from your old n/a engine fit?

Originally Posted by vex

lol. Brian, how are you checking your fuel level (via dash. I assume you're just going to use the motec sensor for the signal)? I'm trying to figure out mapping for my car... and I think I have it nailed, but want to see what you do.

Nah, not the MoTeC sensor, that thing is too big and too expensive. Odd you should bring this up, sorry I didn't see it sooner. I was just about to weld the side on my tank when I was going through my checklist - sender - fucker - I dicked around with the stocker for a bit and decided that it would be too much effort to make it fit, so I'm just going to swing by the chandlery tomorrow and pick up a 9" Wema for my 10" deep tank.
http://www.wemausa.com/tank_sensors/...nk_sensors.htm
If the Wema fails, I'll be able to adapt the stock sender into the mounting hole for the Wema so it's a no brainer. Wema for now, and if the Autometer gauge pisses me off.... I will stab it.

[TitaniumTT]

A few pics of the lack of progress I can't wait till I get my first day off in two weeks on Friday. Maybe I'll try to break my 46 hour record

[Force13b]

Originally Posted by TitaniumTT

A few pics of the lack of progress I can't wait till I get my first day off in two weeks on Friday. Maybe I'll try to break my 46 hour record

[ig]http://rotarycarclub.com/rotary_forum/attachment.php?attachmentid=8185&stc=1&d=127554627 0[/img]

[img]http://rotarycarclub.com/rotary_forum/attachment.php?attachmentid=8186&stc=1&d=127554627 0[img]

[img]http://rotarycarclub.com/rotary_forum/attachment.php?attachmentid=8187&stc=1&d=127554627 0[/mg]

[img]http://rotarycarclub.com/rotary_forum/attachment.php?attachmentid=8188&stc=1&d=127554627 0[/mg]

Can that rubber hosing take gas on the outside of it? I know some rubbers get eaten up when summered in gas

[vex]

Originally Posted by TitaniumTT

A few pics of the lack of progress I can't wait till I get my first day off in two weeks on Friday. Maybe I'll try to break my 46 hour record

Holy multiple fittings BATMAN! Just fab a simpler setup! You know you want to. It will just nag at you until you do it.

You could easily make a single fitting on a lathe. I might even be able to design it up on Autodesk for you

[TitaniumTT]

Originally Posted by wanganwarrior

very nice fab work

Thanks man

Originally Posted by Force13b

Can that rubber hosing take gas on the outside of it? I know some rubbers get eaten up when summered in gas

Yes it can. And for all of you wondering the Aeromotive push-to-fit barb type hose can as well. The exterior is the same material as the interior so it can be submergered. You'll see pics of that tomorrow...... hopefully.

Originally Posted by vex

Holy multiple fittings BATMAN! Just fab a simpler setup! You know you want to. It will just nag at you until you do it.

You could easily make a single fitting on a lathe. I might even be able to design it up on Autodesk for you

If you wanna hook me up I'll DEFINATELY take one. It needs to go from a -6 female to a 5/16" barb. The 5/16 barb is the problem. If it was a 3/8" I could do it with one fitting but it's that fucking 5/16" think that sucks balls.

[WE3RX7]

That looks like SHIT

Seriously though... its looking pretty good, just make sure you get ALL the metal shavings out before you seal it up, lol...

[FC3S Murray]

NICE DUDE!!!

Your work is always stellar!

I am going to start a FS thread this weekend so let me know what you want to do with those "items" when you get some free time bro.....no rush.

[helghast7]

like i said from the very first weld i saw of yours...you put a robots precision and consistency to shame

so glad all my welding is done by you

speaking of your stuff...whats up with those stickers man?? lol

[EJayCe996]

Originally Posted by helghast7

speaking of your stuff...whats up with those stickers man?? lol

whoa whoa whoa..... I WANT IN

[TitaniumTT]

Originally Posted by WE3RX7

That looks like SHIT

Seriously though... its looking pretty good, just make sure you get ALL the metal shavings out before you seal it up, lol...

Thanks man, I'll try to remember that..

Originally Posted by FC3S Murray

NICE DUDE!!!

Your work is always stellar!

I am going to start a FS thread this weekend so let me know what you want to do with those "items" when you get some free time bro.....no rush.

Yeah, I sent ya a PM, we gotta chat Cus ya know, this car isn't done, the FD is outside under a cover, I definately need to start a turbo 'vert project

Originally Posted by helghast7

like i said from the very first weld i saw of yours...you put a robots precision and consistency to shame

so glad all my welding is done by you

speaking of your stuff...whats up with those stickers man?? lol

Thanks Dae, and no worries, glad to help out, now we gotta get into some really custom shit

As for the stickers, next time I see ya I'll let ya know whats going on with that.

[helghast7]

Originally Posted by TitaniumTT

Thanks Dave, and no worries, glad to help out, now we gotta get into some really custom shit

As for the stickers, next time I see ya I'll let ya know whats going on with that.

mmmmmmmmm i like the sound of that

and i cant wait, yay stickers!!! lol