My T2 build

I am still waiting for my Viton oil control o-rings and thermal pellet to show up.




DATED 02-17-08

ok here is some pics of the keg sandwiched together..

yes I forgot to paint the top of the rear iron but it is painted now... and the "13B Mazda" has been sanded down so it is metal color...







DATED 2-17-08

Well I just bought some

84-85 13B NT low impedance square top center port 680cc orange 195500-0900 injectors.

I heard they flow like 720cc injector on FC's so these will be my secondary injectors..

I am sending out my other injectors (550cc's) to get them cleaned and flowed so I can use two of them for primarys



DATED 02-18-08

See thats cool to hear. I like hearing success stories cause then that gives me confidence...

today I bought:
a tube of hylomar (in my posession)

from Pineapple Racing I purchased:
Medium street port template
exhaust port template
S4 T2 omp block off plate
S4 T2 air control valve block off plate
crank sensor cover plate (with ninja )
omp injector block off plugs


so I should see those before the weekend...

I cant wait I get to start porting here very soon.. I am so siked!!!


DATED 02-19-08

Well while I await my pats to show up I have cleaned up the work bench down stairs and I am going to pull all of the parts on it ...

Yes Brian this is where the porting will take place lol..

I will update with any more info or pics as things change


DATED 02-20-08

My purchase from Atkins showed up today

Viton oil control o-rings and the thermal pellet.



more to come after my Pineapple Racing purchase shows up

DATED 02-22-08
ok so today I have received

From Xboxthug360:
S4 T2 ECU
S4 T2 afm
S4 T2 water pump housing

From Pineapple Racing:
street port template
exhaust port template
crank sensor cover (ninja)
ACV block off plate
S4 omp block off plate
OMP injector plugs (however I just realized I only bought 1 pair...)

I will take pics tonight when I get home...

I also just bought from Japan2LA:
both S4 T2 fuel rails
SS clutch hose

just bought my walbro 255lph fuel pump.

OK guys here is some pics of the parts that came in and the painting I have done...

Painted CAS



CAS with Pineapple "ninja" cover


S5 thermostat housing (not sure yet if I will use it)


S4 T2 water pump housing



S4 T2 ECU


S4 T2 AFM


Pineapple Racing SP template


Pineapple Racing exhaust porting template


Pineapple Racing block off plates


Painted water pump pulley


Painted crank pulley


Painted front cover



OK thats my updates for today.. I plan to do more work and painting this weekend...

As I receive more or get more done I will post pics and updates...

As of right now including the engine and all the parts I have bought I roughly calculate about 1800.00


DATED 02-24-08

OK today was the day I began to port the irons...

I was quite scared but RX7Tuner was there to push me and make me do it lol...

I used the Pineapple racing template above and gave it the newbie porting Spooled up Racing push lol...

The grinding is done, I need to lots of sanding right now so I will have these done by wednesday I hope....

here is the current pics of the irons... (don't be to mean) lol

Front iron intake port


front iron port




Intermediate iron front port


Intermediate iron intake ports




intermediate iron rear port


Rear iron port job




rear iron intake ports





The mess on the table from afterwards



So what do u think?


I did the front and rear irons and RX7tuner did the intermediate iron... (I did not think he was good enough to handle the bigger ports)

Brian thank you very much for all your help today.. I am going to port the housings tomorrow and get to sanding so Hopefully Friday we can start assembly...

THX again... keep the comments coming..


Well I could not go to bed without getting the exhaust ports cut..

here are the pics, not sure which port is which housing but these are the pics I took.. again I still need to sand but I atleast got it cut tonight..