MaczPayne's Turbo II - Page 5

FC3S Murray · 02-18-2010, 09:20 PM

Quote:

Originally Posted by calicrewchief

Don't give away our secret!

lol

***TitaniumTT*** · 02-19-2010, 02:11 AM

You find me NOAW!

MaczPayne · 02-19-2010, 08:22 PM

Bastards lol!

FC3S Murray · 02-27-2010, 11:53 AM

lol. What is the status Macz?

Max777 · 03-04-2010, 01:16 AM

this thread needs pics.

MaczPayne · 03-09-2010, 03:42 AM

Been wrapping up senior design before I graduate in spring, so I haven't touched the car at all for the past month

I'll be working on it as soon as next week ends

MaczPayne · 03-30-2010, 03:22 PM

Got some work in during the past week:

-Swapped the rear subframes (a PITA job with only one jack)
-Pulled the engine/trans from donor car
-Picked up a new exhaust

Things left:
-Waiting on a radiator, will be picking up a low mileage trans at the same time when it's ready
-Waiting on my wheels at the repair shop
-Motor/trans in the TII needs to be yanked
-Microtech and alarm wiring needs to be yanked
-Wiring, installation, and etc
-Installing (for the second time) the big brake kit
-A re-tune to make sure everything's running right
-New tires
-etc

If I work carefully, it'll be driving around within 3 weeks

Gregory Casimir · 03-31-2010, 12:39 AM

^^ lucky you

MaczPayne · 04-06-2010, 12:14 AM

Two of the wheels are toast, I'm going to hold on to them until I can afford to have new rings and barrels produced.

As for replacement wheels, I ordered a set that I won't be crying over when I ruin them. They're fairly lightweight, and I can wrap the same sized rubbers on them

Big Brakes are back on, but the car will still be stranded on jack-stands since I have no wheels with tires to it down on.

Currently working on the wiring, removing the old from the wrecked, rebuilding and re-looming the engine harness and power harness, and installing them. With luck, I'll have this thing going again in 2 or 3 weeks.

***TitaniumTT*** · 04-06-2010, 12:42 AM

That's what you said a week ago.... is this turning into a "money Pit"

MaczPayne · 04-09-2010, 01:44 AM

Hopefully not haha!

I keep running into things to do, and if I don't do them, they'll always be a splinter in the back of my mind!

Got a track day on the 22nd of May to aim for, hopefully everything works out!

MaczPayne · 05-29-2010, 12:08 AM

Fired her up for the first time in 6 months, damn she sounds good. No pics just yet, I keep forgetting to snap any

Things left to do:

-Finish wiring the instruments
-Bleed the brakes and clutch
-Mount tires
-Get the car smogged and registered
-Shakedown!

MaczPayne · 05-31-2010, 02:54 AM

Drove her last night and today, feels good to be back!

The other wheels need tires, so this will have to do; I still need to get it smogged and registered. Trying out 275's in the rear this time

Pics don't do the interior justice, I've never seen a more mint black interior! All I need now is a rear privacy cover.

MaczPayne · 05-31-2010, 05:46 AM

I was hoping no one caught that, damnit! lol

Gregory Casimir · 05-31-2010, 12:48 PM

wow man nice to see your 7 back man!

02-19-2010, 02:11 AM	#62
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	You find me NOAW! __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

02-19-2010, 08:22 PM	#63
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Bastards lol! __________________ Johnson TA FC in the works!

02-27-2010, 11:53 AM	#64
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana Posts: 611 Rep Power: 17	lol. What is the status Macz? __________________ Same pig, new soul

03-04-2010, 01:16 AM	#65
Max777 Pirate Join Date: Mar 2008 Location: Central IL Posts: 1,323 Rep Power: 19	this thread needs pics. __________________ Rotaries:They are NOT that complicated!

03-09-2010, 03:42 AM	#66
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Been wrapping up senior design before I graduate in spring, so I haven't touched the car at all for the past month I'll be working on it as soon as next week ends __________________ Johnson TA FC in the works!

03-30-2010, 03:22 PM	#67
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Got some work in during the past week: -Swapped the rear subframes (a PITA job with only one jack) -Pulled the engine/trans from donor car -Picked up a new exhaust Things left: -Waiting on a radiator, will be picking up a low mileage trans at the same time when it's ready -Waiting on my wheels at the repair shop -Motor/trans in the TII needs to be yanked -Microtech and alarm wiring needs to be yanked -Wiring, installation, and etc -Installing (for the second time) the big brake kit -A re-tune to make sure everything's running right -New tires -etc If I work carefully, it'll be driving around within 3 weeks __________________ Johnson TA FC in the works!

03-31-2010, 12:39 AM	#68
Gregory Casimir Rotary Fanatic Join Date: Jan 2010 Posts: 253 Rep Power: 16	^^ lucky you

04-06-2010, 12:14 AM	#69
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Two of the wheels are toast, I'm going to hold on to them until I can afford to have new rings and barrels produced. As for replacement wheels, I ordered a set that I won't be crying over when I ruin them. They're fairly lightweight, and I can wrap the same sized rubbers on them Big Brakes are back on, but the car will still be stranded on jack-stands since I have no wheels with tires to it down on. Currently working on the wiring, removing the old from the wrecked, rebuilding and re-looming the engine harness and power harness, and installing them. With luck, I'll have this thing going again in 2 or 3 weeks. __________________ Johnson TA FC in the works!

04-06-2010, 12:42 AM	#70
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	That's what you said a week ago.... is this turning into a "money Pit" __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

04-09-2010, 01:44 AM	#71
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Hopefully not haha! I keep running into things to do, and if I don't do them, they'll always be a splinter in the back of my mind! Got a track day on the 22nd of May to aim for, hopefully everything works out! __________________ Johnson TA FC in the works!

05-29-2010, 12:08 AM	#72
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Fired her up for the first time in 6 months, damn she sounds good. No pics just yet, I keep forgetting to snap any Things left to do: -Finish wiring the instruments -Bleed the brakes and clutch -Mount tires -Get the car smogged and registered -Shakedown! __________________ Johnson TA FC in the works!

05-31-2010, 02:54 AM	#73
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	Drove her last night and today, feels good to be back! The other wheels need tires, so this will have to do; I still need to get it smogged and registered. Trying out 275's in the rear this time Pics don't do the interior justice, I've never seen a more mint black interior! All I need now is a rear privacy cover. __________________ Johnson TA FC in the works! Last edited by MaczPayne; 05-31-2010 at 02:59 AM.

05-31-2010, 05:46 AM	#74
MaczPayne Bah! Join Date: Mar 2008 Location: Riverside, SoCal Posts: 442 Rep Power: 18	I was hoping no one caught that, damnit! lol __________________ Johnson TA FC in the works!

05-31-2010, 12:48 PM	#75
Gregory Casimir Rotary Fanatic Join Date: Jan 2010 Posts: 253 Rep Power: 16	wow man nice to see your 7 back man!