Overheated on track - now what?

[infernosg]

Originally Posted by vex

I hate to say this, but it sounds quite similar to a soft seal letting go. You might want to let the engine sit for a day or two and check to see if you have any pooling coolant in the combustion chamber.

I assume I check this by pulling the EGI fuse and a spark plug and cranking the engine to see if anything comes out? Spark plugs are also something I need to check.

Originally Posted by vex

When mine let go I could easily start it up and run it around town, but as soon as it hit operating temperature the engine would start to run on one rotor. When temperatures got warmer the car got harder and harder to start.

I drove 2.5 hours back home yesterday at speed >70 mi/hr and I'm positive I didn't loose a rotor, or any power for that matter. If I do have a failed coolant o-ring or rotor housing, it must be very small. The weird thing about the hard starting is that it was easier to start it this morning (ambient temperatures ~65F) after sitting all night than it was yesterday afternoon (ambient temperatures ~80F) after only sitting for ~3 hours.

Originally Posted by vex

Also pay attention to dropping coolant levels. You may have a link somewhere (whether it's by the water pump housing, a hose, or internal of the engine).

I have no found any large external leaks, but that doesn't mean much. When I flush the system this weekend I'll get a much better idea of what kind of shape everything is in. As far as I know the radiator, cap and water pump are all original OEM equipment. I'm pretty sure the thermostat was replaced at some point and if it was I'm almost positive it is not an OEM part.

In the meantime I guess I'll just keep an eye out on the coolant level. The coolant level sensor seems overly sensitive to me, but it hasn't come back on in a while. If nothing changes I can only conclude the conditions simply outmatched the car's 22 year-old cooling system and some upgrades are in order.

Originally Posted by 88turboii

it was opposite for me when i had bad coolant seal. it would run on one rotor at start, but after about 15 seconds or so it would run like normal. white smoke on startup, from the coolant puddling in the chambers burning off. that and i could fill the overflow container with a couple 3rd gear pulls lol

Would the white coolant-smoke and smell make it past two catalytic converters? Aside from Magnecor spark plug wires and a K&N drop-in filter my engine is all stock. The exhaust was replaced after the manifold at some point but it looks to be a stock replacement, not a performance modification. I only ask because I see no smoke and don't smell coolant at the tailpipes.

Originally Posted by 88turboii

but yeah i also have overheating problems on the track. it will start creeping past 1/2 way after about 10 minutes of track time, even in cool weather. im still running a tmic, so the radiator should be getting plenty of flow. it was suggested to me to use aluminum tape and seal off all the parts around the radiator that air could get past, but i have not tried that yet

I was about 20 minutes into the session - literally the last lap before cool-down. As far as I know, this is the only time the gauge crept past 1/2 way during all of the sessions. When I heard the buzzer I looked at the gauge and it was just then starting to move from 1/2 way to "H" - it's not like I ran a full lap at WOT with the gauge pegged at "H".

[vex]

Originally Posted by infernosg

I assume I check this by pulling the EGI fuse and a spark plug and cranking the engine to see if anything comes out? Spark plugs are also something I need to check.

If you were closer I'd lend you my bore scope (makes checking things really easy). But yes, you can do it that way too.

I drove 2.5 hours back home yesterday at speed >70 mi/hr and I'm positive I didn't loose a rotor, or any power for that matter. If I do have a failed coolant o-ring or rotor housing, it must be very small. The weird thing about the hard starting is that it was easier to start it this morning (ambient temperatures ~65F) after sitting all night than it was yesterday afternoon (ambient temperatures ~80F) after only sitting for ~3 hours.

Which makes sense if you have a casting give way.

I have no found any large external leaks, but that doesn't mean much. When I flush the system this weekend I'll get a much better idea of what kind of shape everything is in. As far as I know the radiator, cap and water pump are all original OEM equipment. I'm pretty sure the thermostat was replaced at some point and if it was I'm almost positive it is not an OEM part.

In the meantime I guess I'll just keep an eye out on the coolant level. The coolant level sensor seems overly sensitive to me, but it hasn't come back on in a while. If nothing changes I can only conclude the conditions simply outmatched the car's 22 year-old cooling system and some upgrades are in order.

Sounds like a plan.

[RETed]

Originally Posted by infernosg

Spark plugs are also something I need to check.

This should tell you if the engine is bad or not.
No sense guessing everything else unless you get confirmation...


-Ted

[infernosg]

Originally Posted by RETed

This should tell you if the engine is bad or not.
No sense guessing everything else unless you get confirmation...


-Ted

When it stops raining this is my plan - I'll even post pictures when I'm done. I suppose with coolant/water I'm looking for a white/yellow fouled plug?

The car started and ran just fine after work yesterday. No buzzer, no overheating, no weird noise (other than loose belts). Letting is sit for today and I'll see what it does tomorrow morning (pending plugs).

Is it possible the slightly loose airpump belt was not providing enough friction on the water pump and it was slipping at higher RPM?

[RETed]

Originally Posted by infernosg

When it stops raining this is my plan - I'll even post pictures when I'm done. I suppose with coolant/water I'm looking for a white/yellow fouled plug?

Not necessarily...

Typically, if coolant is leaking into the chamber, the spark plug is going to come out clean - it's like if you're running water injection.
If you have the leading versus trailing plugs next to each other, it'll be obvious.


-Ted

[infernosg]

Well I'm pretty sure the engine needs a rebuild, but more on that later. First, spark plug pictures. Rotor 1 first, then rotor 2. Leading is on left, trailing is on right.





So I'm not sure how to read those but I don't think it matters. They weren't wet or anything but you can see the white/brown build up.

Per some suggestions I pulled the EGI fuse, removed the radiator cap and had my wife crank the car with the throttle open. After a few bubbles the fluid level began to rise. After putting everything back together and driving around the block for a bit I noticed that I'm getting a good amount of bubbles coming out of the overflow tube into the overflow bottle. Occasionally there would be periods where some amount of coolant would come out of this tube. Additionally, the upper radiator hose is "hard" when the car is running. Right before I turned the car off the low coolant buzzer came on again. Correct me if I'm wrong, but this all seems to indicate at least a failed water seal and the combustion gases are partially pressurizing the cooling system.

[RETed]

The spark plugs don't look like there's any obvious sign the engine is burning coolant.

With that said, if it's a small coolant leak into the engine, it will not show on the plugs.
Also, failure of the water jacket o-ring could make it possible it won't show on the spark plugs.

The low coolant buzzer triggering could be just because you opened the cap and compromise the cooling system - allowing some air to stay trapped and then trigger the buzzer.

I'm trying to be optimistic at this point.

The only way to tell is to drive it a significant distance and then check the coolant level to see if it significantly dropped (or puked out the overflow).


-Ted

[Pete_89T2]

I agree with Ted on this. The coolant level sensor is pretty sensitive, and when you flush & fill the cooling system, it takes lots of "burping" to get all the trapped air out of the system.

If you can get your hands on a cooling system pressure tester, you can do a quick pressure test to verify if you have a leak or not and find it. Basically this is a quick pressure leak down test - remove the radiator cap, replace it with pressure tester's cap, pump it up to the recommended pressure and watch its gauge for 10~15 minutes. If the pressure drops, you've got a leak - external leaks will be found wherever you see coolant peeing out; internal leaks may not be as easy to find, but if the pressure drops you've got a problem.

Check with your local auto parts chain shop or tool rental shop - you can probably rent a pressure tester for a reasonable cost; just have to make sure they have one with the right cap to fit your radiator.

[infernosg]

After the first "event" I filled up the radiator and managed to drive 2.5 hours home averaging 70 mi/hr with no overheating, but the buzzer would come on occasionally during tighter turns and lower speed driving. Once I got home and the car cooled off I topped off the radiator and bled the system the best I could. At this point the radiator was completely full and the overflow bottle was at the full level as well. I was able to drive to and from work (only 8 miles) with no issues on Monday and I let the car sit most of the day yesterday. Yesterday afternoon, after driving more recklessly than I'd like on the street, I came home and revved the engine in neutral in the driveway. No buzzer while doing all this so I turned it off and let it sit for about 30 minutes. Before starting it up again I noticed the overflow bottle was now ~1" above the "full" mark. I made it to the end of the driveway when the buzzer came on. Since it was still fully warmed up I just pulled back up and turned it off for good. The buzzer did go off as soon as I started to move back up the driveway.

What has me most worried is the constant bubbling I'm getting in the overflow bottle. To ensure it wasn't be caused by engine vibrations I removed the overflow cap and tube and placed it in a cup of clear water. With the car fully warmed up there was a constant stream of tiny bubbles coming out of the pickup tube. Only once did a moderately large amount of coolant get burped into the cup. After that it was back to the bubbles.

Pressure testing is my next step before throwing new parts at it (rad. cap, thermostat, water pump). The plan is to swing by an auto parts store after work to see if they have anything I can rent.

The one thing I can't seem to explain is the original overheating event. IIRC, the cooling system holds like 2 gallons of water and I know I didn't add nearly that much after it overheated. The fact the buzzer came on just as the temperature gauge started to rise also has me stumped considering it has come on many times since that and the temperature gauge hasn't moved.

Originally Posted by RETed

I'm trying to be optimistic at this point.

I am a self proclaimed pessimist and worry constantly, but I'm trying!