My lexus v8 FB build

85turbo12a · 08-24-2012, 08:43 PM

the goal of this project is to build something no one else has, and I think i pretty much nailed that...the technical goals are to have at or slightly over 500whp, with the accompanying 400+wtq, have a cruising MPG of nearly 30mpg and a top speed north of 200mph, <--though I am not really willing to risk my car or my life to try it...car is sketchy above 150 with no aero mods....been there done that...

I had to shorten the T2 trans shifter location by 4 inches to push the engine back, resulting in an interesting mod to the shifter housing and new aluminum Xmember and body mounts.

the RE-speed Xmember had to be shimmed down 3/8, and lightly modded for the motor mount set up, offset bushings lower the rack as far as possible, I also added a 1" rectangle tube to the bottom of it to aid in a strike point to guard engine from road impact, also with provisions for armor plate sump guard, sump has to be shortened 1 inch, but i will make up for the loss of oil volume with the dual external filters and large oil cooler, engine holds 6 quarts originally with small filter and no cooler.

had to relocate the brake proportioning valve to the strut tower to clear the valve cover, pretty easy job.

all this work resulted in being able to close a stock unmodded hood over this tall ass engine and without cutting any sheetmetal on my precious little car.

the choice to use the T2 trans is simple...cost, i already had a forged steel flywheel and nice ACT clutch/pressure plate capable of the HP intended so since i did all the adapters myself for free, all it cost me was about 25 bucks for some special hardware, and then bout 100 bucks for a brand new camry starter since the T2 starter lacks the testicular fortitude to roll over a 4 cam v8, as for the strength of the t2...we shall see, they are pretty tough, my 12a made a good 400+ and i beat it like a stepchild, trans still works and sounds perfect.

FC Zach · 08-24-2012, 11:00 PM

Very neat, you're a talented machinist. Can't wait to see it in person.

08-24-2012, 11:00 PM	#2
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN Posts: 2,267 Rep Power: 20	Very neat, you're a talented machinist. Can't wait to see it in person. __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

08-24-2012, 08:43 PM	#1
85turbo12a nerd Join Date: May 2011 Location: Lakeland Florida Posts: 107 Rep Power: 15	the goal of this project is to build something no one else has, and I think i pretty much nailed that...the technical goals are to have at or slightly over 500whp, with the accompanying 400+wtq, have a cruising MPG of nearly 30mpg and a top speed north of 200mph, <--though I am not really willing to risk my car or my life to try it...car is sketchy above 150 with no aero mods....been there done that... I had to shorten the T2 trans shifter location by 4 inches to push the engine back, resulting in an interesting mod to the shifter housing and new aluminum Xmember and body mounts. the RE-speed Xmember had to be shimmed down 3/8, and lightly modded for the motor mount set up, offset bushings lower the rack as far as possible, I also added a 1" rectangle tube to the bottom of it to aid in a strike point to guard engine from road impact, also with provisions for armor plate sump guard, sump has to be shortened 1 inch, but i will make up for the loss of oil volume with the dual external filters and large oil cooler, engine holds 6 quarts originally with small filter and no cooler. had to relocate the brake proportioning valve to the strut tower to clear the valve cover, pretty easy job. all this work resulted in being able to close a stock unmodded hood over this tall ass engine and without cutting any sheetmetal on my precious little car. the choice to use the T2 trans is simple...cost, i already had a forged steel flywheel and nice ACT clutch/pressure plate capable of the HP intended so since i did all the adapters myself for free, all it cost me was about 25 bucks for some special hardware, and then bout 100 bucks for a brand new camry starter since the T2 starter lacks the testicular fortitude to roll over a 4 cam v8, as for the strength of the t2...we shall see, they are pretty tough, my 12a made a good 400+ and i beat it like a stepchild, trans still works and sounds perfect.