Cooling System Mods

Phoenix7 · 05-02-2008, 12:08 AM

"Another problem Toyo Kogyo experienced that had been seen at NSU was the formation of cracks in the rotor housing around the sparkplug holes. It was determined that they were a result of "thermal shock" or sudden thermal loads placed on the housing when it was taken from a relatively cool temperature and sharply accelerated to 7,000rpm in all gears on a road test. By developing a test bed procedure that could consistently reproduce these conditions, engineers could then do systematic studies on cooling system improvements and their effect at relieving thermal loads. Tests were showing that on cars driven hard immediately after startup, the temperature of the inner wall of the rotor housing reached 450*F within one minute of startup. This abuse consistently produced cracks in the housing around the sparkplug opening after 4000 cycles.

Improvements in the cooling system brought the maximum temperatures of the rotor housing trochodial wall to below 410*F. But the final improvement was the redesign of the housing itself. The bosses for the tension bolts which held the engine together were relieved from the inner wall of the housing, thereby relieving part of the mechanical restrictions on the part that gets the hottest. Repeated testing after this improvement produced no more cracks in the housing."

So this was back in the 70s. They've made the improvements on the engine since then to further reduce this problem.

You lost an apex seal in the rear housing and I'm under the impression that the rear rotors tend to blow due to heat/preignition (cooling problems you're addressing) but it sounds like you may have also over-boosted and caused the sidehousing damage?

Are you monitoring exhaust temps?

Are you going to do the cooling mod and the pump at the same time of will you try the pump first and see if the damage occurs again?

How did you lose the motor (under boost/load)?
What are your mods?
Do you have close up pics of the sparkplug holes?

It's cool that you're documenting and finding things like this. Thanks.

My5ABaby · 05-02-2008, 06:47 AM

Quote:

Originally Posted by phoenix7

So this was back in the 70s. They've made the improvements on the engine since then to further reduce this problem.

Is there any documentation on that? Regardless, it likely still a sizable issue. This is why I get annoyed when people do cold burnouts and stuff. They're just asking for screwed up housings...

Barry Bordes · 05-02-2008, 03:37 PM

Quote:

Originally Posted by phoenix7

"Another problem Toyo Kogyo experienced that had been seen at NSU was the formation of cracks in the rotor housing around the sparkplug holes. It was determined that they were a result of "thermal shock" or sudden thermal loads placed on the housing when it was taken from a relatively cool temperature and sharply accelerated to 7,000rpm in all gears on a road test. By developing a test bed procedure that could consistently reproduce these conditions, engineers could then do systematic studies on cooling system improvements and their effect at relieving thermal loads. Tests were showing that on cars driven hard immediately after startup, the temperature of the inner wall of the rotor housing reached 450*F within one minute of startup. This abuse consistently produced cracks in the housing around the sparkplug opening after 4000 cycles.

Improvements in the cooling system brought the maximum temperatures of the rotor housing trochodial wall to below 410*F. But the final improvement was the redesign of the housing itself. The bosses for the tension bolts which held the engine together were relieved from the inner wall of the housing, thereby relieving part of the mechanical restrictions on the part that gets the hottest. Repeated testing after this improvement produced no more cracks in the housing."

Phoenix7, I would love to read this early research. Even though it is non turbo in its scope.

So this was back in the 70s. They've made the improvements on the engine since then to further reduce this problem.

You lost an apex seal in the rear housing and I'm under the impression that the rear rotors tend to blow due to heat/preignition (cooling problems you're addressing) but it sounds like you may have also over-boosted and caused the sidehousing damage?

Actually my rear housing was a RE type which didn't have the latest 3rd gen cooling mod, which contributed to the failure I'm sure.

Are you monitoring exhaust temps?
Yes, front and rear.

Are you going to do the cooling mod and the pump at the same time of will you try the pump first and see if the damage occurs again?
Both

How did you lose the motor (under boost/load)?
Merging into 70mph traffic.

What are your mods?
RE 13B, ITO large street port, TO4S, HKS cast divided, 50/50 AI

Do you have close up pics of the sparkplug holes?
Yes, but they are not the best.

It's cool that you're documenting and finding things like this. Thanks.

I will put pictures soon. Thank you for your input.
Barry

Barry Bordes · 05-02-2008, 03:50 PM

Quote:

Originally Posted by phoenix7

"Improvements in the cooling system brought the maximum temperatures of the rotor housing trochodial wall to below 410*F. But the final improvement was the redesign of the housing itself. The bosses for the tension bolts which held the engine together were relieved from the inner wall of the housing, thereby relieving part of the mechanical restrictions on the part that gets the hottest. Repeated testing after this improvement produced no more cracks in the housing."

Phoenix7, do you have pictures of how "The bosses for the tension bolts which held the engine together were relieved from the inner wall of the housing". Were they severed completely? The housing wall just floated? For how far?

Very Interesting, Barry

Phoenix7 · 05-02-2008, 05:53 PM

Quote:

Originally Posted by Barry Bordes

Phoenix7, do you have pictures of how "The bosses for the tension bolts which held the engine together were relieved from the inner wall of the housing". Were they severed completely? The housing wall just floated? For how far?

Very Interesting, Barry

No pics at this moment. I'll look and see if I can find the info when I get home. That excerpt came from the most recent book on the rotary egine (released 2007 or 2008) and this section's source was an SAE paper from 30 years ago. I'll let you know which one (in case you can access the SAE papers) in a bit.

Quote:

Originally Posted by Barry Bordes

I actually did two housing mods. The first was to enlarge the passages in the hottest areas next to the sparkplugs as shown in Yamamoto's housing temp diagram.
But use caution! I cut through on the lower side of the Trailing plug. A bad combination of new carbide burs and being too large. 1/4" long shaft would probably be best.

I see! thanks, good stuff.