FC3S Murray's never ending build.

***TitaniumTT*** · 07-07-2009, 07:57 PM

I think the FSM says to use the vaso bacuase they are assuming that the engine is going to be assembled immediately.

I wouldn't put the gas/water seals in dry, I just wouldn't put the vaso on the irons until you're ready to assemble the engine.

I've got the tracking number. Lemme grab it and see what's going on with that. The went out last friday. I understand there was a holiday involved but gimme a flippin break.

BTW - that vid will be in the mail on Thursday. It kinda covers what we're talking about here.

FC3S Murray · 07-07-2009, 09:42 PM

Quote:

Originally Posted by TitaniumTT

I think the FSM says to use the vaso bacuase they are assuming that the engine is going to be assembled immediately.

I wouldn't put the gas/water seals in dry, I just wouldn't put the vaso on the irons until you're ready to assemble the engine.

I've got the tracking number. Lemme grab it and see what's going on with that. The went out last friday. I understand there was a holiday involved but gimme a flippin break.

BTW - that vid will be in the mail on Thursday. It kinda covers what we're talking about here.

Thanks again buddy for all the help. It is very appreciated!

I just went through your thread again for shits and giggles and FUCK you have had a hell of a run. I never saw your cannon plugs in the firewall. I had that same idea back in 07 but got lazy and decided to just rewire the factory harness. I work with those cannon plugs everyday on the F-15/P&W 220's, and back when I was on the F-16 they always inspired me to put them in my 7. Good job!

So update on my build: BDC sent out my irons so I should recieve those by Monday. In addition my rotor should arrive the same time.

All I have left is to clean my good rotor(WD-40 time!!) and order all my water, side and oil seals.

I am a little relucant to clearance my side seals to .05mm....not much room for expansion in case a horrible quick overheat ever happens(which I will in all my control never let happen). Please enlighten me if I am just being a giant vagina but it seems safer.

Payday is Friday so Mazdatrix well get me the shit by friday of next week so.........build starts in two weeks.

07-07-2009, 07:57 PM	#1
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	I think the FSM says to use the vaso bacuase they are assuming that the engine is going to be assembled immediately. I wouldn't put the gas/water seals in dry, I just wouldn't put the vaso on the irons until you're ready to assemble the engine. I've got the tracking number. Lemme grab it and see what's going on with that. The went out last friday. I understand there was a holiday involved but gimme a flippin break. BTW - that vid will be in the mail on Thursday. It kinda covers what we're talking about here. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**