New project: 1976 Cosmo RX-5 - Page 12

rx7 vinnie · 02-26-2014, 11:41 AM

Love meshies.... Timeless look and would compliment the old skool well.

FerociousP · 02-26-2014, 12:27 PM

Stock vert wheels with 205s or 215s. Cheap wheels, cheap tires, look good, Mazda centers, yes they are 6.5" but you have no need for more tire at this time, can easily borrow Curby's for test fit. Doesn't get cheaper or better than that.

85rx-7gsl-se · 02-26-2014, 12:38 PM

I would consider looking into some old school domestic wheels as a vintage mustang pattern would work. Just my worthless 2 cents.

85rx-7gsl-se · 02-26-2014, 01:10 PM

Mayba something like these:

http://www.customwheelsexpress.com/c...ls-p-1737.html

djmtsu · 02-26-2014, 01:53 PM

Quote:

Originally Posted by 85rx-7gsl-se

Mayba something like these:

http://www.customwheelsexpress.com/c...ls-p-1737.html

Those wheels are HEAVY!

85rx-7gsl-se · 02-26-2014, 02:27 PM

True, but you get the general idea. Besides, this isnt a race car lol

djmtsu · 02-26-2014, 03:28 PM

Quote:

Originally Posted by 85rx-7gsl-se

True, but you get the general idea. Besides, this isnt a race car lol

Indeed. However, to make a slower car faster (quicker), lower the weight. Considering that the unsprung weight of the wheels is the greatest to overcome, I would rather have lighter than heavier!!!

djmtsu · 03-12-2014, 09:43 AM

More stuff happening. Pretty much all taken apart, waiting on parts!

What is this malarkey?

Looking pretty.

Here is what is left, and what is happening with the beast.

The GSL-SE stuff is going to have to wait until summer/fall to be fabbed/installed. The front struts and rear axle need to be completely rebuilt, and I don't have the funds for that right now. Since I already rebuilt the Cosmo rear end last fall, I figured fuck it, I'll just run the Cosmo stuff.

Fun fact, the Cosmo rotors are bigger than the GSL-SE stuff....

The front is all apart, waiting on ball joints, sway links, and brake pads to show up. Trans is out and getting resealed. New Exedy clutch is here.

One issue that I found yesterday....the horror of fuel that sat in a tank for 15 years....

Johnny_K · 03-12-2014, 11:38 AM

Pics of rebuild.

Rotor cleaned and springs labeled

Permatex going on prior to Atkins housing o ring

Carefully installing o ring

Lubing up the rotor in preparation for the seals

Spring installed followed by the side seal

Rotor on rear housing

Rotor lubed for eshaft and corner seals and springs going in

Followed by the eshaft

Center iron going on

2nd rotor on, inspecting placement of seals

Front iron going on

How we ended the night

jacobcartmill · 03-13-2014, 03:58 PM

Quote:

Originally Posted by FerociousP

(this assumes you have a center iron with inj bosses, which you'll prob have by the time you swap the bad motor out.)

Quote:

Originally Posted by djmtsu

Who said this motor was bad?

Quote:

Originally Posted by FerociousP

just an assumption. prove me wrong!

Quote:

Originally Posted by djmtsu

Also, when I tore apart the engine I was a little concerned.

Quote:

Originally Posted by djmtsu

Painted before rebuild.

so this is the engine that adler was messing with last weekend at charles'. the housings looked perfect!
so was it pulled, disassembled, cleaned, painted, and put it back together with the original hard seals? why all that work if the engine was good?

not hating, just curious. edit: i'm awaiting an update here with this thing running.

FerociousP · 03-13-2014, 04:07 PM

Those housings did look great. I wonder how much the PO paid for them when the engine was first rebuilt...

djmtsu · 03-13-2014, 04:10 PM

Two reasons why it was pulled.

1). It sat for 15 years (with periodic oil squirt and turns) so even though it had relatively few miles on it, I was concerned the oil control rings would be toast, and they were.

2) Charles and Adler are good men. I'll leave it at that.

djmtsu · 03-13-2014, 04:12 PM

Quote:

Originally Posted by FerociousP

Those housings did look great. I wonder how much the PO paid for them when the engine was first rebuilt...

I used to have the receipt.

$837 for the rebuild in 1988 money.

EDIT: Online inflation calculator says it would cost $1655.01 in 2014 money.

FerociousP · 03-13-2014, 04:25 PM

Quote:

Originally Posted by djmtsu

Two reasons why it was pulled.

1). It sat for 15 years (with periodic oil squirt and turns) so even though it had relatively few miles on it, I was concerned the oil control rings would be toast, and they were.

2) Charles and Adler are good men. I'll leave it at that.

Wow for 15 years of sitting thats pretty good.

jacobcartmill · 03-13-2014, 04:29 PM

DJ, i will go to deal's gap if you get this thing running.

02-26-2014, 11:41 AM	#166
rx7 vinnie I SEE DEAD PEOPLE Join Date: Mar 2008 Location: nashville, tn (antioch) Posts: 743 Rep Power: 18	Love meshies.... Timeless look and would compliment the old skool well. __________________ VIN-AUTO Rotary list of Fails below: 86 mazda rx7 csp 61 N/A= because RACECAR 87 mazda rx7 t2 with 13b-re cosmo GT42= FKN RUNS!!! 03 Dodge Viper SRT-10 Vert 06 dodge ram 2500 Megacab turbo Cummins=puller 16 MB ML350

02-26-2014, 12:27 PM	#167
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro Posts: 1,046 Rep Power: 19	Stock vert wheels with 205s or 215s. Cheap wheels, cheap tires, look good, Mazda centers, yes they are 6.5" but you have no need for more tire at this time, can easily borrow Curby's for test fit. Doesn't get cheaper or better than that. __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

03-12-2014, 09:43 AM	#173
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN Posts: 4,043 Rep Power: 22	More stuff happening. Pretty much all taken apart, waiting on parts! What is this malarkey? Looking pretty. Here is what is left, and what is happening with the beast. The GSL-SE stuff is going to have to wait until summer/fall to be fabbed/installed. The front struts and rear axle need to be completely rebuilt, and I don't have the funds for that right now. Since I already rebuilt the Cosmo rear end last fall, I figured fuck it, I'll just run the Cosmo stuff. Fun fact, the Cosmo rotors are bigger than the GSL-SE stuff.... The front is all apart, waiting on ball joints, sway links, and brake pads to show up. Trans is out and getting resealed. New Exedy clutch is here. One issue that I found yesterday....the horror of fuel that sat in a tank for 15 years.... __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-13-2014, 04:07 PM	#176
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro Posts: 1,046 Rep Power: 19	Those housings did look great. I wonder how much the PO paid for them when the engine was first rebuilt... __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

03-13-2014, 04:10 PM	#177
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN Posts: 4,043 Rep Power: 22	Two reasons why it was pulled. 1). It sat for 15 years (with periodic oil squirt and turns) so even though it had relatively few miles on it, I was concerned the oil control rings would be toast, and they were. 2) Charles and Adler are good men. I'll leave it at that. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-12-2014, 11:38 AM	#174
Johnny_K Rotary Fanatic Join Date: Jun 2013 Posts: 225 Rep Power: 12	Pics of rebuild. Rotor cleaned and springs labeled Permatex going on prior to Atkins housing o ring Carefully installing o ring Lubing up the rotor in preparation for the seals Spring installed followed by the side seal Rotor on rear housing Rotor lubed for eshaft and corner seals and springs going in Followed by the eshaft Center iron going on 2nd rotor on, inspecting placement of seals Front iron going on How we ended the night

03-13-2014, 04:29 PM	#180
jacobcartmill Rotary Fan in Training Join Date: Jun 2011 Posts: 50 Rep Power: 0	DJ, i will go to deal's gap if you get this thing running.