Ceramic Coated Intake Manifold

Swif · 02-20-2011, 12:00 AM

I am selling my ceramic coated upper and lower intake manifold. There were bought to install on my car. I went with the a different lower intake and my car is still not done.

The ceramic coating is stated by the person I bought these from, "Satin Coatings have been tested to exceed over 2000 degrees Fahrenheit without any damage such as lifting, cracking or flaking."

These parts are used. Then have not been installed on a car after the ceramic coating.

I am asking $125 + shipping.

speedjunkie · 02-20-2011, 02:17 AM

Nice. I'm actually getting mine done right now. Well, the LIM will be ceramic but the UIM and all other intake air passages will be powder, but all black. If I hadn't already dropped off my UIM to get done I'd pick this up from you. GLWS.

Swif · 02-20-2011, 10:56 PM

Bump.

Swif · 02-25-2011, 10:04 PM

Bump

1twistedrx7 · 03-01-2011, 09:39 AM

swif who did those for you ?if you don't mind me asking!

Supernaut · 03-03-2011, 03:05 PM

I'm very interested as well.

Swif · 03-08-2011, 04:10 PM

I will see if I can find out who did the coating. I bought these from another forum that had a group buy going on a few years back.

Smokey · 03-09-2011, 11:09 AM

Do you still have the missing stud for the lower manifold? Was it coated in that hole, and if so, have you tried screwing a stud into it? I had a problem previously where bolt holes were coated and it was a pain in the ass.

Swif · 03-09-2011, 11:19 PM

These were done by IR Performance. They are ocated in Metuchen, NJ

I do not have the stud. I have not tried to install a stud. Anything that is paint or coated that has threads I have always ran a thread chaser first. I have not installed this on my car so I did not even run a chaser in them as I was not a t a point to install on my car.

Swif · 03-16-2011, 01:08 PM

Sale pending!

Swif · 03-22-2011, 11:32 PM

Sold!

03-01-2011, 09:39 AM	#5
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 Posts: 411 Rep Power: 0	swif who did those for you ?if you don't mind me asking! __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

03-03-2011, 03:05 PM	#6
Supernaut Rotary Fanatic Join Date: Jun 2010 Location: Edgewater NJ Posts: 265 Rep Power: 15	I'm very interested as well. __________________ -93 Spirit R Replica built @ IRP/S1. S1 tuned

03-09-2011, 11:09 AM	#8
Smokey Long Time Onlooker Join Date: Mar 2008 Location: Columbus, Ohio Posts: 31 Rep Power: 0	Do you still have the missing stud for the lower manifold? Was it coated in that hole, and if so, have you tried screwing a stud into it? I had a problem previously where bolt holes were coated and it was a pain in the ass. __________________ 93 Touring - AD coilovers, BBK, full exhaust, PFS SMIC, PFC

02-20-2011, 02:17 AM	#2
speedjunkie RCC Loves Me Not You Join Date: Mar 2008 Location: Colorado Springs, CO Posts: 2,089 Rep Power: 20	Nice. I'm actually getting mine done right now. Well, the LIM will be ceramic but the UIM and all other intake air passages will be powder, but all black. If I hadn't already dropped off my UIM to get done I'd pick this up from you. GLWS.

02-20-2011, 10:56 PM	#3
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	Bump.

02-25-2011, 10:04 PM	#4
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	Bump

03-08-2011, 04:10 PM	#7
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	I will see if I can find out who did the coating. I bought these from another forum that had a group buy going on a few years back.

03-09-2011, 11:19 PM	#9
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	These were done by IR Performance. They are ocated in Metuchen, NJ I do not have the stud. I have not tried to install a stud. Anything that is paint or coated that has threads I have always ran a thread chaser first. I have not installed this on my car so I did not even run a chaser in them as I was not a t a point to install on my car.

03-16-2011, 01:08 PM	#10
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	Sale pending!

03-22-2011, 11:32 PM	#11
Swif The Newbie Join Date: Apr 2009 Posts: 18 Rep Power: 0	Sold!